1、Designation:D790314(Reapproved 2020)Standard Practice forDetermining the Capacity of Oxygen Removal Ion ExchangeCartridges1This standard is issued under the fixed designation D7903;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the
2、year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This practice covers the determination of the perfor-mance of oxygen removal ion exchange resin cartridges in there
3、generated form when used for removing dissolved oxygenfrom water.The test can be used to determine the initialcapacity of unused cartridges or the remaining capacity of usedcartridges.In this case,performance is defined as oxygenremoval capacity(or throughput)to a defined endpoint.1.2 The values sta
4、ted in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health
5、,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of Internation
6、al Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D888 Test Methods for Dissolved Oxygen in WaterD1129 Terminology Relating to WaterD1193 Specification for Reagent Water3.Terminology3.1 D
7、efinitions:3.1.1 For definitions of terms used in this standard,refer toTerminology D1129.4.Summary of Practice4.1 This practice will evaluate the capacity of an oxygenremoval cartridge for water by running a test solution of knownoxygen content through a cartridge to a specified endpoint.Thevolume
8、will enable a determination of the capacity for thecartridge to remove dissolved oxygen in water.5.Significance and Use5.1 This practice can be used to evaluate unused oxygenremoval ion exchange cartridges for conformance to specifi-cations.5.2 This practice provides for the calculation of capacity
9、interms of the volume of water treated to an end point level ofdissolved oxygen.5.3 The practice as written assumes that the oxygen removalion exchange resins in the cartridge are either partially or fullyregenerated.Regeneration of the resins is not part of thispractice.5.4 This practice provides f
10、or the calculation of capacity ona cartridge basis.5.5 This practice may be used to test different size oxygenremoval resin cartridges.The flow rate of test water and thefrequency of sampling are varied to compensate for theapproximate volume of resin in the test cartridge.6.Apparatus6.1 Test assemb
11、ly(Fig.1),consisting of the following:6.1.1 Cartridge,and pressure vessel,if required.Connec-tions shall be provided at the top and the bottom for theadmission and removal of the exhausting solution as describedin 8.3,8.4,and 8.5.6.1.2 Test solution tank.Adequate means of regulating andmeasuring flo
12、w through the cartridge shall be provided.If thetest flow rate(8.2)cannot be obtained by gravity feed,then apump should be used.Make sure all fittings,connections,andwetted pump portals are secure and tight to the atmosphere.1This practice is under the jurisdiction of ASTM Committee D19 on Water and
13、is the direct responsibility of Subcommittee D19.08 on Membranes and IonExchange Materials.Current edition approved Nov.1,2020.Published November 2020.Originallyapproved in 2014.Last previous edition approved in 2014 as D7903 14.DOI:10.1520/D7903-14R20.2For referenced ASTM standards,visit the ASTM w
14、ebsite,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis
15、international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)C
16、ommittee.6.1.3 Measuring oxygen levels of the water in the input andthe output of the test cartridge in accordance with Test MethodsD888.A continuous recorder is recommended.7.Reagents7.1 Purity of ReagentsReagent grade chemicals shall beused in all tests.Unless otherwise indicated,it is intended thatall reagents shall conform to the specifications of the Commit-tee on Analytical Reagents of the American Chemical Society,where such specifications are available.3Other grades may beused,provided i
