1、Designation:D734220Standard Test Method forProlonged Worked Stability of Lubricating Grease inPresence of Water(Water Stability Test)1This standard is issued under the fixed designation D7342;the number immediately following the designation indicates the year oforiginal adoption or,in the case of re
2、vision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This test method covers a procedure for determining theshear stability of lubricating grease in the pre
3、sence of water(wet shear stability)by a full scale grease worker.This testmethod is also known as the water stability test.1.2 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.3 This standard does not purport to address all of t
4、hesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accor-dan
5、ce with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standar
6、ds:2D217 Test Methods for Cone Penetration of LubricatingGreaseD1193 Specification for Reagent WaterD4057 Practice for Manual Sampling of Petroleum andPetroleum Products3.Terminology3.1 Definitions:3.1.1 consistency,nof lubricating grease,degree of resis-tance to movement under stress.3.1.1.1 Discus
7、sionThe term consistency is used somewhatsynonymously with penetration.Generally,consistency refersto the worked penetration of a grease.D2173.1.2 lubricating grease,nsemi-fluid to solid product of adispersion of a thickener in a liquid lubricant.3.1.2.1 DiscussionThe dispersion of the thickener for
8、ms atwo-phase system and immobilizes the liquid lubricant bysurface tension and other physical forces.Other ingredients arecommonly included to impart special properties.D2173.1.3 penetration,nof lubricating grease,depth that thestandard cone,when released to fall under its own weight for5 s,enters
9、the sample.D2173.1.4 prolonged worked penetration,nof lubricatinggrease,the penetration of a sample after it has been workedmore than 60 double strokes in a standard grease worker at atemperature of 15 C to 30 C(59 F to 86 F).3.1.4.1 DiscussionAfter the prescribed number of doublestrokes,the worker
10、and contents are brought to 25 C(77 F),worked an additional 60 double strokes,and penetrated withoutdelay.3.1.5 thickener,nin lubricating grease,substance com-posed of finely divided particles dispersed in a liquid lubricantto form the products structure.3.1.5.1 DiscussionThe thickener can be fibers
11、(such asvarious metallic soaps)or plates or spheres(such as certainnon-soap thickener)which are insoluble or,at most,only veryslightly soluble in liquid lubricant.The general requirementsare that the solid particles be extremely small,uniformlydispersed,and capable of forming a relatively stable,gel
12、-likestructure with the liquid lubricant.D2173.1.6 worked penetration,nof lubricating grease,thepenetration at 25 C,without delay,of a sample after 60 doublestrokes in a standard grease worker.D2173.1.7 working,nof lubricating grease,subjection of asample to the shearing action of the standard greas
13、e worker.D2173.2 Definitions of Terms Specific to This Standard:3.2.1 wet shear stability,nof lubricating grease,change inconsistency of a mixture of sample and small amount of waterafter a specified amount of working in a grease worker.1This test method is under the jurisdiction of ASTM Committee D
14、02 onPetroleum Products,Liquid Fuels,and Lubricants and is the direct responsibility ofSubcommittee D02.G0.02 on Consistency and Related Rheological Tests.Current edition approved June 1,2020.Published September 2020.Originallyapproved in 2007.Last previous edition approved in 2015 as D7342 15.DOI:1
15、0.1520/D7342-20.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end o
16、f this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.4.Summary of Test Method4.1 A grease sample mixed with a small
