收藏 分享(赏)

ASTM_D_7983_-_17_2022.pdf

上传人:益****师 文档编号:171462 上传时间:2023-03-04 格式:PDF 页数:4 大小:80.84KB
下载 相关 举报
ASTM_D_7983_-_17_2022.pdf_第1页
第1页 / 共4页
ASTM_D_7983_-_17_2022.pdf_第2页
第2页 / 共4页
ASTM_D_7983_-_17_2022.pdf_第3页
第3页 / 共4页
ASTM_D_7983_-_17_2022.pdf_第4页
第4页 / 共4页
亲,该文档总共4页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation:D798317(Reapproved 2022)Standard Test Method forShrinkage of Carpet Backing Fabrics1This standard is issued under the fixed designation D7983;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A num

2、ber in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers the procedure for evaluatingshrinkage,in both wet and dry conditions,of woven,knittedand nonwoven backing fabrics desi

3、gned for use in the manu-facture of pile yarn floor coverings.Determination of carpetbacking shrinkage was previously contained within Test Meth-ods D2646.For consistency,Subcommittee D13.21 extractedthis portion and created a separate test method.1.2 The values stated in inch-pound units are to be

4、regardedas the standard.The values given in parentheses are mathemati-cal conversions to SI units that are provided for informationonly and are not considered standard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of th

5、e user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established

6、in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D123 Terminology Relating to TextilesD1776 Practice for Conditioning and T

7、esting TextilesD2646 Guide for Backing Fabric Characteristics of PileYarnFloor CoveringsD5684 Terminology Relating to Pile Floor CoveringsE177 Practice for Use of the Terms Precision and Bias inASTM Test Methods3.Terminology3.1 For definitions of terms relating to Pile Floor Coverings,D13.21,refer t

8、o Terminology D5684.3.1.1 The following terms are relevant to this standard:backing fabric,nonwoven fabric,shrinkage.3.1.2 For all other terminology related to textiles,refer toTerminology D123.4.Summary of Test Method4.1 HOT WET ProcedureThe backing fabric is first mea-sured to a specific length in

9、 each principle direction.The fabricthen is immersed in hot distilled or deionized water,dried,andremeasured.The shrinkage is calculated as the change in lengthexpressed as a percentage of the length before immersion.4.2 HOT DRY ProcedureThe backing fabric is first mea-sured to a specific length in

10、each principle direction.The fabricis then exposed to dry heat and remeasured.The shrinkage iscalculated as the change in length expressed as a percentage ofthe length before exposure.5.Significance and Use5.1 This test method can be useful in characterizing andcomparing shrinkage properties of both

11、 primary and secondarybacking fabrics.This test method is considered satisfactory foracceptance testing of commercial shipments because currentestimates of between-laboratory precision are acceptable,andthis test method is commonly used in the trade for acceptancetesting.5.1.1If there are difference

12、s of practical significancebetween reported test results for two laboratories(or more),comparative tests should be performed to determine if there isstatistical bias between them using competent statistical assis-tance.As a minimum,use test samples for such comparativetests that are as homogeneous a

13、s possible,drawn from the samelot of material as the samples that resulted in the disparateresults during initial testing,and that are randomly assigned inequal numbers to each laboratory for testing.The test resultsfrom the laboratories should be compared using statistical testfor unpaired data at

14、a probability level chosen prior to thetesting series.If a bias is found either its cause must be foundand corrected,or future test results for that material must beadjusted in consideration of the known bias.1This test method is under the jurisdiction ofASTM Committee D13 on Textilesand is the dire

15、ct responsibility of Subcommittee D13.21 on Pile Floor Coverings.Current edition approved March 1,2022.Published March 2022.Originallyapproved in 2017.Last previous edition approved in 2017 as D7983-17.DOI:10.1520/D7983-17R22.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orconta

16、ct ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2