1、Designation:D745019Standard Specification forPerformance of Rear Axle Gear Lubricants Intended for APICategory GL-5 Service1This standard is issued under the fixed designation D7450;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the
2、 year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This specification covers test methods and acceptancecriteria for determining the acceptability of gear oils fora
3、pplications that specify a lubricant meeting the performancerequirements of API Category GL-5 service.Lubricants thatmeet these performance requirements are typically intended foruse in automotive axles,particularly those containing hypoidgears,operating under various combinations of high-speed/shoc
4、k-load and low-speed/high-torque conditions.1.2 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.3 This standard does not purport to addr
5、ess all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.4 This international standard was developed
6、in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1
7、ASTM Standards:2D130 Test Method for Corrosiveness to Copper from Petro-leum Products by Copper Strip TestD892 Test Method for Foaming Characteristics of Lubricat-ing OilsD5704 Test Method for Evaluation of the Thermal andOxidative Stability of Lubricating Oils Used for ManualTransmissions and Final
8、 Drive AxlesD6121 Test Method for Evaluation of Load-Carrying Capac-ity of Lubricants Under Conditions of Low Speed andHigh Torque Used for Final Hypoid Drive AxlesD7038 Test Method for Evaluation of Moisture CorrosionResistance of Automotive Gear LubricantsD7452 Test Method for Evaluation of the Lo
9、ad CarryingProperties of Lubricants Used for Final Drive Axles,Under Conditions of High Speed and Shock LoadingD8165 Test Method for Evaluation of Load-Carrying Capac-ity of Lubricants Used in Hypoid Final-Drive AxlesOperated under Low-Speed and High-Torque Conditions2.2 Military Standards:3MIL-L-21
10、05C Lubricating Oil,Gear,MultipurposeMIL-L-2105D Lubricating Oil,Gear,MultipurposeMIL-PRF-2105E Lubricating Oil,Gear,Multipurpose2.3 SAE Documents:4J306 Automotive Gear Lubricant Viscosity ClassificationJ2360 Lubricating Oil,Gear Multipurpose(Metric)MilitaryUse3.Terminology3.1 Definitions:3.1.1 ridg
11、ing,non ring and pinion gears,an alteration ofthe tooth surface to give a series of parallel raised and polishedridges running diagonally in the direction of sliding motion,either partially or completely across the tooth surfaces of gears.D61213.1.2 rippling,non ring and pinion gears,an alteration o
12、fthe tooth surface to give an appearance of a more or lessregular pattern resembling ripples on water or fish scales.D61213.1.3 pitting,non ring and pinion gears,small irregularcavities in the tooth surface,resulting from the breaking out ofsmall areas of surface metal.D61211This specification is un
13、der the jurisdiction of ASTM Committee D02 onPetroleum Products,Liquid Fuels,and Lubricants and is the direct responsibility ofSubcommittee D02.B0 on Automotive Lubricants.Current edition approved May 1,2019.Published June 2019.Originallyapproved in 2008.Last previous edition approved in 2013 as D74
14、50 13.DOI:10.1520/D7450-19.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from Standardization Documen
15、ts Order Desk,DODSSP,Bldg.4,SectionD,700RobbinsAve.,Philadelphia,PA19111-5098,http:/www.dodssp.daps.mil4Available from Society of Automotive Engineers(SAE),400 CommonwealthDr.,Warrendale,PA 15096-0001,http:/www.sae.org.*A Summary of Changes section appears at the end of this standardCopyright ASTM I
16、nternational,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 3.1.4 spalling,non ring and pinion gears,the breakingout of flakes of irregular area of the
