1、Designation:D753209(Reapproved 2021)Standard Practice forDetermination of Re-tack Ability of Carpet Adhesives1This standard is issued under the fixed designation D7532;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last
2、revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This practice will provide a protocol for determining theeffect of extended drying(open time)periods on the shear andpeel streng
3、th performance of a carpet adhesive when bondinga carpet backing or standard duck cloth material to a substrate.1.2 The values stated in SI units are to be regarded as thestandard.The values given in parentheses are for informationonly.1.3 This standard does not purport to address all of thesafety c
4、oncerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accor-dance with in
5、ternationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D907 T
6、erminology of AdhesivesD6004 Test Method for Determining Adhesive ShearStrength of Resilient Flooring and Carpet AdhesivesD6862 Test Method for 90 Degree Peel Resistance ofAdhesives2.2 Voluntary Product Standards:3PS1 Construction and Industrial Plywood3.Terminology3.1 Definitions:3.1.1 Many of the
7、terms in this test method are defined inTerminology D907.3.1.2 re-tack,nan industry term used to describe anadhesive performance characteristic when the original applica-tion is modified to include an extended adhesive open timeperiod followed by re-application of pressure to bond thecarpet to the s
8、ubstrate.3.1.3 standard conditions,n23 6 2C(73 6 3F)and50%relative humidity.4.Summary of Practice4.1 This practice is for a comparison of shear strength and90 degree peel strength performance between a standard duckcloth material versus a specific carpet backing.Performancetesting occurs after an ap
9、plied test adhesive has been exposedto standard conditions ambient air for various open timeperiods.It should be noted that the use of duck cloth isnecessary since there is no bench mark or standardized carpetbacking currently produced in the United States.5.Significance and Use5.1 Selection of or d
10、evelopment of a carpet adhesive,fordirect glue or adhered applications requires knowledge of theadhesives ability to perform adequately when it is foundnecessary to correct an installation concern,such as bubbles orwrinkles,by re-rolling or application of dead weight to theaffected area without the
11、application or injection of additionaladhesive.5.2 Adhesive bonding of some carpet backings to substratesand the adhesive bonding of carpet backings to a padfoundation,double stick or glue application,require that priorto bonding the adhesive is to be dried sufficiently to allow forno transfer of ad
12、hesive as a result of slight finger pressure.6.Apparatus6.1 Applicator Trowel,with a notch pattern of 3.2 mm(18in.)wide,2.4 mm(332in.)deep,3.2 mm(18in.)flat.NOTE1Adhesive manufacturer application instructions may recom-mend different trowel notching design.6.2 Six 1 kg(2.2 lb)dead weights.6.3 Testin
13、g Equipment in accordance with the test method tobe implemented.6.4 Timer.1This practice is under the jurisdiction of ASTM Committee D14 on Adhesivesand is the direct responsibility of Subcommittee D14.10 on Working Properties.Current edition approved April 1,2021.Published April 2021.Originallyappr
14、oved in 2009.Last previous edition approved in 2016 as D7532 09(2016).DOI:10.1520/D7532-09R21.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summ
15、ary page onthe ASTM website.3Available from U.S.Government Printing Office Superintendent of Documents,732 N.Capitol St.,NW,Mail Stop:SDE,Washington,DC 20401,http:/www.access.gpo.gov.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis inte
16、rnational standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.17.Materials7.1 AdhesiveAn adhesive classified as appropriate for theintended application.7.2 Duck Cloth4Natural,untreated,#10,417.6 g(14.73oz).7.3 CarpetThe carpet specimen with backing attached
