收藏 分享(赏)

ASTM_D_8166_-_21a.pdf

上传人:益****师 文档编号:171743 上传时间:2023-03-04 格式:PDF 页数:8 大小:189.59KB
下载 相关 举报
ASTM_D_8166_-_21a.pdf_第1页
第1页 / 共8页
ASTM_D_8166_-_21a.pdf_第2页
第2页 / 共8页
ASTM_D_8166_-_21a.pdf_第3页
第3页 / 共8页
ASTM_D_8166_-_21a.pdf_第4页
第4页 / 共8页
ASTM_D_8166_-_21a.pdf_第5页
第5页 / 共8页
ASTM_D_8166_-_21a.pdf_第6页
第6页 / 共8页
亲,该文档总共8页,到这儿已超出免费预览范围,如果喜欢就下载吧!
资源描述

1、Designation:D816621aStandard Test Method forSizing and Counting Particulates in Middle Distillate Fuelsand Biodiesel Blend(B6 to B20)Using Continuous Flow andBottle Sampler Automatic Particle Condition Monitors1This standard is issued under the fixed designation D8166;the number immediately followin

2、g the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This test method uses spec

3、ific automatic particle condi-tion monitors(PCMs)to count and measure the size ofdispersed dirt particles,water droplets and other particulates,inmiddle distillate fuel,in the overall range from 4 m to 70 mand in the size bands 4 m,6 m,14 m,and 30 m.1.2 This test method has interim repeatability pre

4、cisiononly,see Section 14 for more information.NOTE1ASTM specification fuels falling within the scope of this testmethod include Specifications:D975,D1655,D3699,D7467,MIL-DTL-83133,MIL-DTL-5624,and distillate grades of D396 and D2880.NOTE2For the purposes of this test method,water droplets arecounte

5、d as particles,and agglomerated particles are detected and countedas a single larger particle.Dirt includes microbial particulates.Althoughthe projected area of a particle is measured,this is expressed as thediameter of a circle for the purposes of this test method.The detector isunable to distingui

6、sh between dirt and water particles.NOTE3This test method may be used for particle sizes bands up to70 m,however the interim repeatability has only been determined for thesize bands 4 m,6 m,and 14 m.All measurements are counts permillilitre.1.3 The values stated in SI units are to be regarded asstan

7、dard.No other units of measurement are included in thisstandard.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mi

8、ne the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations

9、issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D396 Specification for Fuel OilsD975 Specification for Diesel FuelD1655 Specification for Aviation Turbine FuelsD2880 Specification for Gas Turbine Fuel OilsD3699 Specification f

10、or KerosineD4057 Practice for Manual Sampling of Petroleum andPetroleum ProductsD4175 Terminology Relating to Petroleum Products,LiquidFuels,and LubricantsD4177 Practice for Automatic Sampling of Petroleum andPetroleum ProductsD4306 Practice for Aviation Fuel Sample Containers forTests Affected by T

11、race ContaminationD5854 Practice for Mixing and Handling of Liquid Samplesof Petroleum and Petroleum ProductsD6300 Practice for Determination of Precision and BiasData for Use in Test Methods for Petroleum Products,Liquid Fuels,and LubricantsD7467 Specification for Diesel Fuel Oil,Biodiesel Blend(B6

12、 to B20)D7619 Test Method for Sizing and Counting Particles inLight and Middle Distillate Fuels,by Automatic ParticleCounter2.2 U.S.Dept.of Defense Specifications:3MIL-DTL-5624 Specification:Turbine Fuel,Aviation,Grades JP-4(NATO F-40 and JP-5(NATO F-44)MIL-DTL-83133 Specification:Turbine Fuel,Aviat

13、ion,Kerosene Type,JP-8(NATO F-34),NATO F-35,andJP-8+100(NATO F-37)2.3 ISO Standards:4ISO 12103 Road vehiclesTest contaminants for filterevaluationPart 1:Arizona test dust1This test method is under the jurisdiction of ASTM Committee D02 onPetroleum Products,Liquid Fuels,and Lubricants and is the dire

14、ct responsibility ofSubcommittee D02.14 on Stability,Cleanliness and Compatibility of Liquid Fuels.Current edition approved March 1,2021.Published March 2021.Originallyapproved in 2017.Last previous edition approved in 2021 as D8166 21.DOI:10.1520/D8166-21A.2For referenced ASTM standards,visit the A

15、STM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available online at ASSIST Quick Search(http:/quicksearch.dla.mil).4Available from American National Standa

16、rds Institute(ANSI),25 W.43rd St.,4th Floor,New York,NY 10036,http:/www.ansi.org.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2