1、Designation:D803316Standard Classification System forPoly(Ether Ether Ketone)(PEEK)Molding and ExtrusionMaterials1This standard is issued under the fixed designation D8033;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of l
2、ast revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This classification system covers poly(ether ether ke-tone)materials suitable for injection molding and extrusion.This class
3、ification system allows for the use of recycledmaterials provided that all specification requirements are met.1.2 The properties included in this standard are thoserequired to identify the compositions covered.Other require-ments necessary to identify particular characteristics importantto specializ
4、ed applications are to be specified by using thesuffixes in Section 5.1.3 This classification system and subsequent line callout(specification)are intended to provide means of calling outpoly(ether ether ketone)materials used in the fabrication of enditems or parts.It is not intended for the selecti
5、on of materials.It is recommended that material selection be made by thosehaving expertise in the plastics field only after careful consid-eration of the design and the performance required of the part,the environment to which it will be exposed,the fabricationprocess to be employed,the cost involve
6、d,and the inherentproperties of the material other than those covered by thisspecification.1.4 Poly(ether ether ketone),commonly referred to asPEEK,is a member of the poly(aryl ether ketone)or PAEKfamily.Specification D6262 covers properties of PAEK shapesand includes shapes produced from PEEK.NOTE1
7、There is no known ISO equivalent to this standard.1.5 The following precautionary caveat pertains only to thetest method portion,Section 11,of this classification system:This standard does not purport to address all of the safetyconcerns,if any,associated with its use.It is the responsibilityof the
8、user of this standard to establish appropriate safety andhealth practices and determine the applicability of regulatorylimitations prior to use.2.Referenced Documents2.1 ASTM Standards:2D149 Test Method for Dielectric Breakdown Voltage andDielectric Strength of Solid Electrical Insulating Materialsa
9、t Commercial Power FrequenciesD256 Test Methods for Determining the Izod PendulumImpact Resistance of PlasticsD257 Test Methods for DC Resistance or Conductance ofInsulating MaterialsD570 Test Method for Water Absorption of PlasticsD618 Practice for Conditioning Plastics for TestingD638 Test Method
10、for Tensile Properties of PlasticsD648 Test Method for Deflection Temperature of PlasticsUnder Flexural Load in the Edgewise PositionD790 Test Methods for Flexural Properties of Unreinforcedand Reinforced Plastics and Electrical Insulating Materi-alsD792 Test Methods for Density and Specific Gravity
11、(Rela-tive Density)of Plastics by DisplacementD883 Terminology Relating to PlasticsD1600 Terminology forAbbreviated Terms Relating to Plas-ticsD2863 Test Method for Measuring the Minimum OxygenConcentration to Support Candle-Like Combustion ofPlastics(Oxygen Index)D3171 Test Methods for Constituent
12、Content of CompositeMaterialsD3641 Practice for Injection Molding Test Specimens ofThermoplastic Molding and Extrusion MaterialsD3418 Test Method for Transition Temperatures and En-thalpies of Fusion and Crystallization of Polymers byDifferential Scanning CalorimetryD3801 Test Method for Measuring t
13、he Comparative BurningCharacteristics of Solid Plastics in a Vertical PositionD3835 Test Method for Determination of Properties ofPolymeric Materials by Means of a Capillary RheometerD3892 Practice for Packaging/Packing of Plastics1This test method is under the jurisdiction of ASTM Committee D20 on
14、Plasticsand is the direct responsibility of Subcommittee D20.15 on Thermoplastic Materi-als.Current edition approved Dec.1,2016.Published December 2016.DOI:10.1520/D8033-16.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annua
15、l Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 D4000 Classification System for Specifying Plastic Materi-alsD4812 Test Method for
16、Unnotched Cantilever Beam ImpactResistance of PlasticsD5630 Test Method for Ash Content in PlasticsD5740 Guide for Writing Material Standards in the Classi-fication FormatD6262 Specification for Extruded,Compression Molded,and Injection Molded Basic Shapes of Poly(aryl etherketone)(PAEK)D6869 Test Method for Coulometric and Volumetric Deter-mination of Moisture in Plastics Using the Karl FischerReaction(the Reaction of Iodine with Water)D7209 Guide for Waste Reduction,Resource Recovery,andUse of
