1、Designation:D80718Standard Practice forAssessing the Tendency of Industrial Boiler Waters toCause Embrittlement(USBM Embrittlement DetectorMethod)1,2This standard is issued under the fixed designation D807;the number immediately following the designation indicates the year oforiginal adoption or,in
2、the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This practice,3known as the embrittlement-detectormethod,covers the apparatus and procedur
3、e for determiningthe embrittling or nonembrittling characteristics of the water inan operating boiler.The interpretation of the results shall berestricted to the limits set forth in 8.6.NOTE1Cracks in a specimen after being subjected to this test indicatethat the boiler water can cause embrittlement
4、 cracking,but not that theboiler in question necessarily has cracked or will crack.1.2 The effectiveness of treatment to prevent cracking,aswell as an indication of whether an unsafe condition exists,areshown by this practice.Such treatments are evaluated in termsof method specimen resistance to fai
5、lure.1.3 The practice may be applied to embrittlement resistancetesting of steels other than boiler plate,provided that aduplicate,unexposed specimen does not crack when bent 90on a 2-in.(51-mm)radius.1.4 The values stated in inch-pound units are to be regardedas standard.The values given in parenth
6、eses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.5 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate saf
7、ety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of I
8、nternational Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:5A108 Specification for Steel Bar,Carbon and Alloy,Cold-FinishedA515/A515M Specification for Pressure Vessel Plates,Car-bon Stee
9、l,for Intermediate-and Higher-Temperature Ser-viceD1129 Terminology Relating to WaterD1193 Specification for Reagent WaterE3 Guide for Preparation of Metallographic SpecimensE883 Guide for ReflectedLight PhotomicrographyE1351 Practice for Production and Evaluation of FieldMetallographic Replicas3.Te
10、rminology3.1 Definitions:3.1.1 For definitions of terms used in this standard,refer toTerminology D1129.3.2 Definitions of Terms Specific to This Standard:3.2.1 embrittlement cracking,na form of metal failurethat occurs in steam boilers at riveted joints and at tube ends,the cracking being predomina
11、ntly intercrystalline.3.2.1.1 DiscussionThis form of cracking,which has beenknown as“caustic embrittlement,”is believed to result fromthe action of certain constituents of concentrated boiler waterupon steel under stress.For a detailed discussion as to whatcracking should be considered significant f
12、or the purpose ofthis practice,see 8.6.1This test method is under the jurisdiction of ASTM Committee D19 on Waterand is the direct responsibility of Subcommittee D19.03 on Sampling Water andWater-Formed Deposits,Analysis of Water for Power Generation and Process Use,On-Line Water Analysis,and Survei
13、llance of Water.Current edition approved Oct.15,2018.Published October 2018.Originallyapproved in 1944.Last previous edition approved in 2014 as D807 14.DOI:10.1520/D0807-18.2United States Bureau of Mines.3This test method was developed during an investigation conducted under acooperative agreement
14、between the Joint Research Committee on Boiler FeedwaterStudies and the United States Bureau of Mines.For information on the developmentof this test method reference may be made to the following:Schroeder and Berk,1941(1);4Schroeder,Berk,and Stoddard,1941(2);Transactions of the AmericanSociety of Me
15、chanical Engineers,1942(3);Whirl and Purcell,1942(4);and Berkand Schroeder,1943(5).5For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page on
16、the ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 4.Summary of Practice4.1 For embrittlement cracking of the
