1、Designation:D7336/D7336M22Standard Test Method forStatic Energy Absorption Properties of HoneycombSandwich Core Materials1This standard is issued under the fixed designation D7336/D7336M;the number immediately following the designation indicates theyear of original adoption or,in the case of revisio
2、n,the year of last revision.A number in parentheses indicates the year of lastreapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method determines the static energy absorptionproperties(compressive crush stress and crush stroke)
3、ofhoneycomb sandwich core materials.These properties areusually determined for design purposes in a direction normal tothe plane of the face sheets(also referred to as the facing plane)as the honeycomb core material would be placed in a structuralsandwich construction.1.2 Permissible core materials
4、are limited to those in hon-eycomb form.1.3 This test method is not intended for use in crush testingof stabilized honeycomb core materials(for which the facingplane surfaces of the honeycomb core material are dipped inresin to resist local crushing)or sandwich specimens(forwhich facings are bonded
5、to the honeycomb core material).1.4 UnitsThe values stated in either SI units or inch-pound units are to be regarded separately as standard.Thevalues stated in each system are not necessarily exact equiva-lents;therefore,to ensure conformance with the standard,eachsystem shall be used independently
6、of the other,and valuesfrom the two systems shall not be combined.1.4.1 Within the text,the inch-pound units are shown inbrackets.1.5 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish a
7、ppro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theD
8、evelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2C271/C271M Test Method for Density of Sandwich CoreMaterialsD883 Terminology Relating to PlasticsD3878 Terminolo
9、gy for Composite MaterialsD5229/D5229M Test Method for MoistureAbsorption Prop-erties and Equilibrium Conditioning of Polymer MatrixComposite MaterialsE4 Practices for Force Calibration and Verification of Test-ing MachinesE6 Terminology Relating to Methods of Mechanical TestingE18 Test Methods for
10、Rockwell Hardness of Metallic Ma-terialsE122 Practice for Calculating Sample Size to Estimate,WithSpecified Precision,the Average for a Characteristic of aLot or ProcessE177 Practice for Use of the Terms Precision and Bias inASTM Test MethodsE456 Terminology Relating to Quality and Statistics3.Termi
11、nology3.1 DefinitionsTerminology D3878 defines terms relatingto high-modulus fibers and their composites,as well as termsrelating to sandwich constructions.Terminology D883 definesterms relating to plastics.Terminology E6 defines termsrelating to mechanical testing.Terminology E456 and PracticeE177
12、define terms relating to statistics.In the event of aconflict between terms,Terminology D3878 shall have prece-dence over the other terminologies.NOTE1If the term represents a physical quantity,its analyticaldimensions are stated immediately following the term(or letter symbol)infundamental dimensio
13、n form,using the following ASTM standard sym-bology for fundamental dimensions,shown within square brackets:Mfor mass,L for length,T for time,for thermodynamic temperature,and nd for non-dimensional quantities.Use of these symbols is restrictedto analytical dimensions when used with square brackets,
14、as the symbolsmay have other definitions when used without the brackets.1This test method is under the jurisdiction of ASTM Committee D30 onComposite Materials and is the direct responsibility of Subcommittee D30.09 onSandwich Construction.Current edition approved May 1,2022.Published May 2022.Origi
15、nallyapproved in 2007.Last previous edition approved in 2016 as D7336/D7336M 16.DOI:10.1520/D7336_D7336M-22.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards
16、 Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.13.2 Definitions of Terms Specific t
