1、Designation:D76/D76M21Standard Specification forTensile Testing Machines for Textiles1This standard is issued under the fixed designation D76/D76M;the number immediately following the designation indicates the yearof original adoption or,in the case of revision,the year of last revision.A number in
2、parentheses indicates the year of last reapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers the operating characteristics ofthree types of tensile testing machines used for the determina-tion of the force-elongatio
3、n properties of textile materials.These types of tensile testing machines are:1.1.1 Constant-rate-of-extension,CRE.1.1.2 Constant-rate-of-traverse,CRT.1.1.3 Constant-rate-of-loading(force),CRL.1.2 Specifications for tensile testing machines to measureother tensile-related properties of textile mater
4、ials not coveredby this standard are given in the ASTM standards using thosemachines.1.3 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard.The values stated ineach system are not necessarily exact equivalents;therefore,toensure conformance with the sta
5、ndard,each system shall beused independently of the other,and values from the twosystems shall not be combined.1.4 The following safety hazards caveat pertains only to thetest methods described in this specification:This standard doesnot purport to address all of the safety concerns,if any,associate
6、d with its use.It is the responsibility of the user of thisstandard to establish appropriate safety,health,and environ-mental practices and determine the applicability of regulatorylimitations prior to use.1.5 This international standard was developed in accor-dance with internationally recognized p
7、rinciples on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D123 Terminology Relating to Tex
8、tilesD2256 Test Method for Tensile Properties of Yarns by theSingle-Strand MethodD4849 Terminology Related to Yarns and FibersE4 Practices for Force Verification of Testing MachinesE74 Practices for Calibration and Verification for Force-Measuring Instruments3.Terminology3.1 For terminology related
9、to tensile testing,see Terminol-ogy D4849.3.1.1 The following terms are relevant for this standard:bench marks,calibrate,capacity,clamp,constant-rate-of ex-tension type tensile testing machine(CRE),constant-rate-of-load tensile testing machine(CRL),constant-rate-of-traversetensile testing machine(CR
10、T),effective carriage mass,effec-tive gauge length,grip,jaw face,jaw liner,jaws,least count,nominal gauge length,response time,sensitivity,in electronicsystems,sensitivity,stress,tensile testing machine,test skein,time-to-break,true gauge length.3.1.2 For all other terminology related to textiles,se
11、eTerminology D123.4.Performance Requirements4.1 Individual ASTM methods for tensile testing of textilematerials that prescribe apparatus which conforms to thisspecification shall also include such other detailed specifica-tions as may be necessary to describe the testing machine andits operation com
12、pletely.4.1.1 This specification shall not be construed as beingintended to preclude the evolution of improved methods oftesting or testing apparatus,which is recognized as being vitalin an advancing technology.1This specification is under the jurisdiction of ASTM Committee D13 onTextiles and is the
13、 direct responsibility of Subcommittee D13.58 on Yarns andFibers.Current edition approved July 1,2021.Published August 2021.Originallyapproved in 1920.Last previous edition approved in 2016 as D76 11(2016).DOI:10.1520/D0076_D0076M-21.2For referenced ASTM standards,visit the ASTM website,www.astm.org
14、,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandardsvolume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standa
15、rd was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.14.2 Compar
16、ison of results from tensile testing machinesoperating on different principles is not recommended.Whenthese machines are used for comparison testing however,constant time-to-break at 20 6 3 s is the established way ofproducing data,but even then the data may differ significantly.4.2.1 Comparison of test data from machines of the sametype,especially two or more CRT-type or two or moreCRL-type machines,requires consideration of the effect ofindividual machine characteristics;for example,inertia ef
