1、Designation:D777417Standard Test Method forFlexural Fatigue Properties of Plastics1This standard is issued under the fixed designation D7774;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parent
2、heses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This test method covers the determination of dynamicfull reversed fatigue properties of plastics in flexure.Thismethod is applicable to rigid and semi-rig
3、id plastics.Stress andstrain levels are below the proportional limit of the materialwhere the strains and stresses are relatively elastic.Three-pointor four-point bending systems are used to determine theseproperties.1.2 This test method can be used with two procedures:1.2.1 Procedure A,designed for
4、 materials that use three-point loading systems to determine flexural strength.Three-point loading system is used for this procedure.1.2.2 Procedure B,designed for materials that use four-point loading systems to determine flexural strength.Four-point loading system is used for this procedure.1.3 Co
5、mparative tests can be run in accordance with eitherprocedure,provided that the procedure is found satisfactory forthe material being tested.1.4 The values stated in SI units are to be regarded as thestandard.The values provided in parentheses are for informa-tion only.1.5 This standard does not pur
6、port to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.NOTE1This standard and ISO 13003 address the sam
7、e subject matter,but differ in technical content and results cannot be directly comparedbetween the two test methods.1.6 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopmen
8、t of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D618 Practice for Conditioning Plastics for TestingD638 Test Method for Tensile Properties of PlasticsD790 Test Methods f
9、or Flexural Properties of Unreinforcedand Reinforced Plastics and Electrical Insulating Materi-alsD792 Test Methods for Density and Specific Gravity(Rela-tive Density)of Plastics by DisplacementD883 Terminology Relating to PlasticsD1505 Test Method for Density of Plastics by the Density-Gradient Tec
10、hniqueD2839 Practice for Use of a Melt Index Strand for Deter-mining Density of PolyethyleneD3479/D3479M Test Method for Tension-Tension Fatigueof Polymer Matrix Composite MaterialsD4883 Test Method for Density of Polyethylene by theUltrasound Technique(Withdrawn 2017)3D5947 Test Methods for Physica
11、l Dimensions of SolidPlastics SpecimensD6272 Test Method for Flexural Properties of Unreinforcedand Reinforced Plastics and Electrical Insulating Materi-als by Four-Point BendingE4 Practices for Force Verification of Testing MachinesE83 Practice for Verification and Classification of Exten-someter S
12、ystemsE1942 Guide for Evaluating Data Acquisition Systems Usedin Cyclic Fatigue and Fracture Mechanics Testing2.2 ISO Standard:ISO 13003Fibre-Reinforced PlasticsDetermination ofFatigue Properties Under Cyclic Loading Conditions43.Terminology3.1 DefinitionsDefinitions applying to this test methodappe
13、ar in Terminology D883.1This test method is under the jurisdiction of ASTM Committee D20 on Plasticsand is the direct responsibility of Subcommittee D20.10.24 on Fracture and Fatigue.Current edition approved May 1,2017.Published May 2017.Last previousedition approved in 2012 as D7774-12.DOI:10.1520/
14、D7774-17.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is
15、 referenced onwww.astm.org.4Available from American National Standards Institute(ANSI),25 W.43rd St.,4th Floor,New York,NY 10036,http:/www.ansi.org.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 194
16、28-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 3.2 mean strainthe algebraic average of the maximum andminimum strains in one cycle.3.3 mean stressthe algebraic average of the maximum andminimum stresses in one
