1、Designation:D6484/D6484M20Standard Test Method forOpen-Hole Compressive Strength of Polymer MatrixComposite Laminates1This standard is issued under the fixed designation D6484/D6484M;the number immediately following the designation indicates theyear of original adoption or,in the case of revision,th
2、e year of last revision.A number in parentheses indicates the year of lastreapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method determines the open-hole compressivestrength of multidirectional polymer matrix composite lami-n
3、ates reinforced by high-modulus fibers.The composite mate-rial forms are limited to continuous-fiber or discontinuous-fiber(tape or fabric,or both)reinforced composites in which thelaminate is balanced and symmetric with respect to the testdirection.The range of acceptable test laminates and thick-n
4、esses are described in 8.2.1.1.2 Several related ASTM standards reference the proce-dures and apparatus described within this test method.Inparticular,the support fixture described in 7.2 is used byseveral other standards to stabilize compression-loaded testspecimens.These include Practice D6742/D67
5、42M,whichcovers filled-hole compression testing;Practice D7615/D7615M,which covers open-hole fatigue testing;and PracticeD8066/D8066M,which covers unnotched laminate compres-sion testing.1.3 UnitsThe values stated in either SI units or inch-pound units are to be regarded separately as standard.Theva
6、lues stated in each system are not necessarily exact equiva-lents;therefore,to ensure conformance with the standard,eachsystem shall be used independently of the other,and valuesfrom the two systems shall not be combined.1.3.1 Within the text,the inch-pound units are shown inbrackets.1.4 This standa
7、rd does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.5 This internatio
8、nal standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee
9、.2.Referenced Documents2.1 ASTM Standards:2D792 Test Methods for Density and Specific Gravity(Rela-tive Density)of Plastics by DisplacementD883 Terminology Relating to PlasticsD2584 Test Method for Ignition Loss of Cured ReinforcedResinsD2734 Test Methods for Void Content of Reinforced PlasticsD3039
10、/D3039M Test Method for Tensile Properties of Poly-mer Matrix Composite MaterialsD3171 Test Methods for Constituent Content of CompositeMaterialsD3878 Terminology for Composite MaterialsD5229/D5229M Test Method for MoistureAbsorption Prop-erties and Equilibrium Conditioning of Polymer MatrixComposit
11、e MaterialsD5687/D5687M Guide for Preparation of Flat CompositePanels with Processing Guidelines for Specimen Prepara-tionD6742/D6742M Practice for Filled-Hole Tension and Com-pression Testing of Polymer Matrix Composite LaminatesD7615/D7615M Practice for Open-Hole Fatigue Responseof Polymer Matrix
12、Composite LaminatesD8066/D8066M Practice Unnotched Compression Testingof Polymer Matrix Composite LaminatesE4 Practices for Force Verification of Testing MachinesE6 Terminology Relating to Methods of Mechanical TestingE83 Practice for Verification and Classification of Exten-someter SystemsE122 Prac
13、tice for Calculating Sample Size to Estimate,WithSpecified Precision,the Average for a Characteristic of aLot or ProcessE177 Practice for Use of the Terms Precision and Bias inASTM Test MethodsE456 Terminology Relating to Quality and Statistics1This test method is under the jurisdiction of ASTM Comm
14、ittee D30 onComposite Materials and is the direct responsibility of Subcommittee D30.05 onStructural Test Methods.Current edition approved Oct.1,2020.Published November 2020.Originallyapproved in 1999.Last previous edition approved in 2014 as D6484/D6484M 14.DOI:10.1520/D6484_D6484M-20.2For referenc
15、ed ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocke
16、n,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1E691 Practice for Conducting an Interlaboratory Study toDetermine the Precision of a Test Method3.Terminology3.1 DefinitionsTerminology D3878 defines terms
