1、Designation:D7694/D7694M18Standard Test Methods forSelf-Adhesive Modified Bituminous Sheet Material1This standard is issued under the fixed designation D7694/D7694M;the number immediately following the designation indicates theyear of original adoption or,in the case of revision,the year of last rev
2、ision.A number in parentheses indicates the year of lastreapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 Thesetestmethodscovertestproceduresforprefabricated,reinforced,self-adhesive(SA)polymer-modifiedbituminous sheet materials designed
3、 for single-or multiple-plyapplication in roofing and waterproofing membranes.1.2 These test methods specifically address the self-adhesive characteristics of modified bituminous sheetmaterials,and are intended as a supplement to those found inTest Methods D5147/D5147M.1.3 The values stated in eithe
4、r SI units or inch-pound unitsare to be regarded separately as standard.The values stated ineach system are not necessarily exact equivalents;therefore,toensure conformance with the standard,each system shall beused independently of the other,and values from the twosystems shall not be combined.1.4
5、This standard may involve hazardous materials,operations,and equipment.This standard does not purport toaddress all of the safety concerns,if any,associated with itsuse.It is the responsibility of the user of this standard toestablish appropriate safety,health,and environmental prac-tices and determ
6、ine the applicability of regulatory limitationsprior to use.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations
7、issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D146/D146M Test Methods for Sampling and TestingBitumen-Saturated Felts and Woven Fabrics for Roofingand WaterproofingD3167 Test Method for Floating Roller Peel Resistance ofAdhe
8、sivesD1079 Terminology Relating to Roofing and WaterproofingD5147/D5147M Test Methods for Sampling and TestingModified Bituminous Sheet MaterialE177 Practice for Use of the Terms Precision and Bias inASTM Test MethodsE691 Practice for Conducting an Interlaboratory Study toDetermine the Precision of
9、a Test Method3.Significance and Use3.1 These test methods are used to evaluate the properties ofself-adhesive modified bituminous membranes.The resultsdetermine compliance with the applicable specifications,orthey can be used for comparative analysis.3.2 The test methods apply to“as manufactured”mat
10、erialand may not apply to material that has been weathered or ispast the manufacturers recommended shelf life.4.Sampling4.1 From each shipment or fraction thereof,select at randoma number of rolls equal to one half the cube root of the totalnumber rolls of the lot.If the calculated number is fractio
11、nal,express it as the next highest whole number.For convenience,a table showing the number of rolls to be selected from the lotsof various sizes is given in Test Method D146/D146M.4.2 The minimum sample shall consist of five rolls.Therolls so selected constitute the representative sample used forall
12、 subsequent observations and tests pertaining to the lot ofmaterial being tested.4.3 When mutually agreed upon by the concerned parties,other sampling frequencies may be used and reported withinthe framework of these procedures.5.Adhesion to Plywood5.1 ScopeThis test method covers the determination
13、of theadhesive properties of the product sheets to a standardizedplywood substrate,as set forth in Test Method D3167 except asnoted below.The method also allows for the evaluation of amembrane installation over the standardized substrate treatedwith a primer.5.2 ConditioningTesting and conditioning
14、is to be per-formed at test temperatures 23 6 2C 73 6 4F and 4 6 1C1These test methods are under the jurisdiction of ASTM Committee D08 onRoofing and Waterproofing and is the direct responsibility of Subcommittee D08.04on Felts,Fabrics and Bituminous Sheet Materials.Current edition approved Dec.1,20
15、18.Published January 2019.DOI:10.1520/D7649_D7694M-18.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright AS
16、TM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 40 6 2F unless otherwise specified.The plywood must beconditioned at test temperatures f
