1、Designation:D653812(Reapproved 2019)Standard Guide forSampling Wastewater With Automatic Samplers1This standard is issued under the fixed designation D6538;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A n
2、umber in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This guide covers the selection and use of automaticwastewater samplers,including procedures for their use inobtaining representative sample
3、s.Automatic wastewater sam-plers are intended for the unattended collection of samples thatare representative of the parameters of interest in the waste-water body.While this guide primarily addresses the samplingof wastewater,the same automatic samplers may be used tosample process streams and natu
4、ral water bodies.1.2 The guide does not address general guidelines forplanning waste sampling activities(see Guide D4687),devel-opment of data quality objectives(see Practice D5792),thedesign of monitoring systems and determination of the numberof samples to collect(see Guide D6311),operational deta
5、ils ofany specific type of sampler,in-situ measurement of param-eters of interest,data assessment and statistical interpretationof resultant data(see Guide D6233),or sampling and fieldquality assurance(see Guide D5612).It also does not addresssampling groundwater.1.3 The values stated in SI units ar
6、e to be regarded asstandard.No other units of measurement are included in thisstandard.1.3.1 ExceptionThe inch-pound units given in parenthesesare for information only.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of th
7、e user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established
8、in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D4687 Guide for General Planning of Waste SamplingD5088 Practice for Decon
9、tamination of Field EquipmentUsed at Waste SitesD5612 Guide for Quality Planning and Field Implementa-tion of a Water Quality Measurement ProgramD5681 Terminology for Waste and Waste ManagementD5792 Practice for Generation of Environmental Data Re-lated to Waste Management Activities:Development ofD
10、ata Quality ObjectivesD6233 Guide for Data Assessment for Environmental WasteManagement Activities(Withdrawn 2016)3D6311 Guide for Generation of Environmental Data Relatedto Waste Management Activities:Selection and Optimiza-tion of Sampling Design3.Terminology3.1 DefinitionsFor definitions of terms
11、 used in this guide,refer to Terminology D5681.4.Significance and Use4.1 This guide provides persons responsible for designingand implementing wastewater sampling programs with a sum-mary of the types of automatic wastewater samplers,discussesthe advantages and disadvantages of the different types o
12、fsamplers,and addresses recommended procedures for theiruse.The field settings are primarily,but not limited to,openchannel flows in enclosed(e.g.,sewer)systems or open(e.g.,streams or open ditches,and sampling pressure lines)systems.5.Automatic Versus Manual Sampling(2,3)45.1 The advantages and dis
13、advantages of manual and auto-matic sampling are summarized in Table 1.The decision as towhether to use manual or automatic sampling involves manyconsiderations in addition to equipment costs.In general,1This guide is under the jurisdiction of ASTM Committee D34 on WasteManagement and is the direct
14、responsibility of Subcommittee D34.01.03 onSampling Equipment.Current edition approved Sept.1,2019.Published September 2019.Originallyapproved in 2000.Last previous edition approved in 2012 as D6538 12.DOI:10.1520/D6538-12R19.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orconta
15、ct ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.4The boldface numbers given in parentheses refer to a li
16、st of references at theend of the standard.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 manual sampling is indicated when
