1、Designation:D666509(Reapproved 2019)Standard Practice forEvaluation of Aging Resistance of Pre-stressed PrepaintedMetal in a Boiling Water Test1This standard is issued under the fixed designation D6665;the number immediately following the designation indicates the year oforiginal adoption or,in the
2、case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This practice can be used to evaluate the resistance of apre-stressed prepainted metal panel t
3、o cracking and loss ofadhesion,or both,after accelerated aging by boiling water.Most coil coated products are formed and bent into specificshapes to produce a final product.These operations introducestresses,which may be relieved by cracking of the coating afteraging.1.2 This standard does not purpo
4、rt to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.3 This international standard was
5、developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Doc
6、uments2.1 ASTM Standards:2D2794 Test Method for Resistance of Organic Coatings tothe Effects of Rapid Deformation(Impact)D4145 Test Method for Coating Flexibility of PrepaintedSheetE643 Test Method for Ball Punch Deformation of MetallicSheet Material3.Apparatus3.1 Boiling water bath big enough to ho
7、ld formed testspecimens.3.2 10 magnifier(optional).3.3 Scotch#610 adhesive tape or equivalent.4.Reagents4.1 Deionized or other water,as agreed upon by customerand vendor.5.Test Specimen5.1 Bumped,bent,drawn or otherwise deformed samples,tobe agreed upon between customer and vendor.These should bepre
8、pared according to Test Methods D2794,D4145,E643,and/or prepared in a manner agreed upon by customer andvendor.6.Procedure6.1 Examine the test specimens for cracking,flowering andtape pick-off(adhesion loss),and record the results.6.2 Place the formed test specimens in the boiling waterbath for one(
9、1)min.Different times may be used if agreedupon by customer and vendor.6.3 Remove the test specimens and allow them to air dryand cool to room temperature.6.4 Inspect the test specimens for cracking,flowering andadhesion loss,then repeat the tape adhesion test.7.Report7.1 Report the observations reg
10、arding cracking,floweringand adhesion loss.7.2 The degree of cracking,flowering and tape pick-offallowed should be agreed upon by customer and vendor.Report cracking,flowering and tape pick-off noted beforeboiling water aging,and cracking and tape pick-off noted afterboilingwateraging.Whenknown,repo
11、rtsubstrate,pretreatment,coating system,production or preparation dateand any other information request agreed upon between vendorand customer.8.Keywords8.1 aging;bend;boiling water;coil;cracking;deformation;drawn metal;fabrication;flexibility;flowering;impact;pick-off;prepaint;stresses;tape-off1Thi
12、s practice is under the jurisdiction of ASTM Committee D01 on Paint andRelated Coatings,Materials,and Applications and is the direct responsibility ofSubcommittee D01.53 on Coil Coated Metal.Current edition approved Dec.1,2019.Published December 2019.Originallyapproved in 2001.Last previous edition
13、approved in 2014 as D6665 09(2014).DOI:10.1520/D6665-09R19.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyrig
14、ht ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Sta
15、ndards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard.Users of this standard are expressly adv
16、ised that determination of the validity of any such patent rights,and the riskof infringement of such rights,are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised,either reapproved or withdrawn.Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters.Your comments will receive ca
