1、Designation:D6358191Standard Classification System and Basis for Specification forPoly(Phenylene Sulfide)(PPS)Injection Molding,Extrusionand Blow Molding Materials Using ISO Methods1This standard is issued under the fixed designation D6358;the number immediately following the designation indicates t
2、he year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1NOTEEditorially corrected Table PPS in July 2019.1.Scope*1.1 This
3、classification system covers unfilled,reinforcedfilled,and impact modified materials suitable for injectionmolding,extrusion and blow molding using ISO methods.Thesystem allows for the use of poly(phenylene sulfide)(PPS)plastic materials that are recycled,reconstituted recycled-regrind,recovered or
4、reprocessed,or both,provided that therequirements as stated in this specification are met.It is theresponsibility of the supplier and the buyer of recycled,reconstituted,recycled-regrind,recovered or reprocessed,orboth,poly(phenylene sulfide)plastic materials to ensurecompliance(see Guide D7209).1.2
5、 The properties included in this classification are thoserequired to identify the compositions covered.It is possiblethat other requirements are necessary to identify particularcharacteristics important to specialized applications.The use ofsuffixes as shown in Section 5 is one way of specifying the
6、serequirements.1.3 This classification system and subsequent line callout(specification)are intended to provide a means of calling outplastic materials used in the fabrication of end items or parts.It is not intended for the selection of materials.Materialselection needs to be made by those having e
7、xpertise in theplastic field after careful consideration of the design and theperformance required of the part,the environment to which itwill be exposed,the fabrication process to be employed,thecosts involved,and the inherent properties of the material otherthan those covered by this classificatio
8、n.1.4 The following precautionary caveat pertains only to thetest method portion,Section 11,of this classification system:This standard does not purport to address all of the safetyconcerns,if any,associated with its use.It is the responsibilityof the user of this standard to establish appropriate s
9、afety,health,and environmental practices and determine the appli-cability of regulatory limitations prior to use.NOTE1This standard and ISO 28078 address the same subject matter,but differ in technical content.NOTE2ASTM D4067 for PPS uses ASTM test methods.1.5 This international standard was develop
10、ed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2
11、.1 ASTM Standards:2D618 Practice for Conditioning Plastics for TestingD883 Terminology Relating to PlasticsD1600 Terminology forAbbreviated Terms Relating to Plas-ticsD3641 Practice for Injection Molding Test Specimens ofThermoplastic Molding and Extrusion MaterialsD3892 Practice for Packaging/Packi
12、ng of PlasticsD4000 Classification System for Specifying Plastic Materi-alsD4067 Classification System and Basis for Specification forReinforced and Filled Poly(Phenylene Sulfide)(PPS)Injection Molding and Extrusion Materials Using ASTMMethodsD7209 Guide for Waste Reduction,Resource Recovery,andUse
13、of Recycled Polymeric Materials and Products(With-drawn 2015)3E29 Practice for Using Significant Digits in Test Data toDetermine Conformance with Specifications1This classification system is under the jurisdiction ofASTM Committee D20 onPlastics and is the direct responsibility of Subcommittee D20.1
14、5 on ThermoplasticMaterials(Section D20.15.17).Current edition approved April 1,2019.Published May 2019.Originallyapproved in 1998.Last previous edition approved in 2011 as D6358-11.DOI:10.1520/D6358-19E01.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Ser
15、vice at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.*A Summary of Changes section appears at the end of this standardCopyright A
16、STM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 2.2 IEC and ISO Standards:4IEC 60112 Recommended Methods for Determining theComparative
