1、Designation:D653200(Reapproved 2022)Standard Test Method forEvaluation of the Effect of Clear Water Repellent Treatmentson Water Absorption of Hydraulic Cement MortarSpecimens1This standard is issued under the fixed designation D6532;the number immediately following the designation indicates the yea
2、r oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method evaluates the effectiveness of clearwater rep
3、ellents on hydraulic cement mortar specimens basedon water absorption after a water soak.1.2 The values stated in SI units are to be regarded as thestandard.The values given in parentheses are for informationonly.1.3 This standard does not purport to address all of thesafety concerns,if any,associat
4、ed with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accor-dance with internationally recognize
5、d principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2C109/C109M Test Method for Co
6、mpressive Strength ofHydraulic Cement Mortars(Using 2-in.or 50 mm CubeSpecimens)D1475 Test Method for Density of Liquid Coatings,Inks,and Related ProductsD3924 Specification for Standard Environment for Condi-tioning and Testing Paint,Varnish,Lacquer,and RelatedMaterialsE145 Specification for Gravit
7、y-Convection and Forced-Ventilation Ovens3.Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 clear water repellent,na coating formulated for thepurpose of protecting porous substrates by reducing the pen-etration of liquid water.4.Summary of Test Method4.1 The masonry unit is immer
8、sed in a clear water repellent,removed and allowed to cure at ambient condition for 7 days.Any deviations should be noted in 10.1.2.After cure,themasonry unit is weighed and placed in water to a depth of 6.3mm(14in.)for 3 days.After the immersion period,themasonry unit is removed and reweighed.The w
9、ater repellencyvalue of the treatment is then calculated using a comparison tountreated control specimens.5.Significance and Use5.1 Siliceous alkaline substrates are subject to water damagethat may result in deterioration.Water repellents can provideprotection of siliceous alkaline substrates expose
10、d to water.This test method is used to evaluate the efficacy of clear waterrepellents on alkaline substrates.6.Apparatus6.1 Forced Draft Oven,Type 1B,in accordance with theType Section of Specification E145.6.2 Balance,having a capacity of not less than 400 g,andsensitivity of 0.01 g.6.3 Reservoir W
11、ater Pan,capable of maintaining the waterlevel at 6.3 mm(14in.)in depth with noncorroding rods for thespecimens to sit off the bottom.6.4 Stiff Bristle Brush,to brush the masonry units.6.5 Pressurized Air Source,to blow residual material off thebrushed masonry units.1This test method is under the ju
12、risdiction of ASTM Committee D01 on Paintand Related Coatings,Materials,and Applications and is the direct responsibility ofSubcommittee D01.47 on Concrete,Stone and Masonry Treatments.Current edition approved June 1,2022.Published July 2022.Originally approvedin 2000.Last previous edition approved
13、in 2014 as D6532 00(2014).DOI:10.1520/D6532-00R22.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM I
14、nternational,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Gu
15、ides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.16.6 Stopwatch.7.Reagents and Materials7.1 Masonry Units,51 by 51 by 51 mm(2 by 2 by 2 in.)masonry units prepared in accordance with procedures outlinedin Test Method C109/C109M with the form re
16、lease oil re-moved can be used.8.Procedure8.1 Select substrates needed,brush,and blow off dust withpressurized air.The specimens must be free of loose materialthat may be lost and alter the weight.They also must be free ofmaterial that will alter the absorption characteristics.8.2 Label each piece.Run triplicate samples for each waterrepellent treatment.Also include three untreated controlsamples for each series.All specimens in one series of testingshould come from the same lot of masonry units
