1、Designation:D668601(Reapproved 2013)Standard Test Method forEvaluation of Tannin Stain Resistance of Coatings1This standard is issued under the fixed designation D6686;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last
2、revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method is an accelerated procedure to deter-mine the effectiveness of latex coatings at preventing themigration of tan
3、nin stains from wood substrates.1.2 The values in SI units are to be regarded as the standard.The values in parenthesis are for information only.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard
4、 to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2D1475 Test Method For Density of Liquid Coatings,Inks,and Related ProductsD4585 Practice for Testing Water Resistance of CoatingsUs
5、ing Controlled CondensationD5068 Practice for Preparation of Paint Brushes for Evalu-ation3.Terminology3.1 Definitions:3.1.1 tannin stain resistance,nthe ability of a coating toprevent the migration of tannins or other wood-based chromo-spheres to the surface of a film.4.Summary of Test Method4.1 Th
6、is test method utilizes a condensation test chamber todetermine the tannin stain resistance of latex paints.The testpaints are applied to substrates that contain tannin extractivesand are placed on or in the test chamber.CIELAB L*and b*values as well as subjective ratings are recorded after exposure
7、.5.Significance and Use5.1 Tannins and other chromophoric extractives are natu-rally occurring materials in wood and wood-based substrates.Tannins are prevalent to a high degree in cedar,redwood,oakand to a lesser degree in white and yellow pine.Tannins arealso present in varying amounts in wood com
8、position products.These extractives are solubilized and darkened in color byaqueous coatings,resulting in unsightly yellow or browndiscolorations.This test method is designed to show therelative ability of paints to prevent tannin bleed-through.Typically cedar or redwood panels are used for this tes
9、t.6.Apparatus6.1 Test Chamber,as described in Practice D4585.6.2 Test Substrate,15.2 by 121.9 cm(6 by 48 in.)substrateor of a size agreed upon by the purchaser and seller of thecoating being tested.6.3 Paint Brush,nylon/polyester brush of good quality.6.4 Spectrophotometer.6.5 Electronic Balance.6.6
10、 Conditioned Room,at 18 to 29.5C(65 to 85F)and 40to 60%relative humidity.7.Reagents and Materials7.1 Wood PanelsSuch as cedar,redwood,oak,white pine,yellow pine or other substrate as agreed upon between thepurchaser and the seller of the coating being tested.7.2 Control PaintAn agreed-upon paint of
11、known tanninstain resistance.7.3 Test PaintsSince there are no standard panels,photographs,or paints for this test method,an agreed-uponcontrol paint(7.2)should be included as one of the test paints.8.Procedure8.1 Choose a substrate with a consistent grain pattern.Patterns vary greatly from panel to
12、 panel,so try to select aboard that has consistent wood grain across the length of thesubstrate.Results may vary from panel to panel because ofdifferent growth rates,grain angles,colors and species ofwood.If necessary,panels may be sanded to remove raisedgrain.Substrates with areas of rough spots sh
13、ould be avoided,1This test method is under the jurisdiction of ASTM Committee D01 on Paintand Related Coatings,Materials,and Applications and is the direct responsibility ofSubcommittee D01.42 on Architectural Coatings.Current edition approved Feb.1,2013.Published February 2013.Originallyapproved in
14、 2001.Last previous edition approved in 2008 as D6686 01(2008)2.DOI:10.1520/D6686-01R13.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary pa
15、ge onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 as they will bleed through more readily.Divide substrate intostrips at least 15.2 cm(6 in.)wide or as agreed upon betweenthe purchaser and the seller and label the back
16、 of each test areawith paint designation.The control paint should be placed nearthe middle of the panel.8.2 Prepare the cabinet as described in Practice D4585.8.3 Prepare paint brush as described in Practice D5068.8.4 Prime all edges of the panels with an appropriate primerand allow to dry according to manufacturers recommenda-tions.The backside of the panels must also be primed if thepanels are to be placed fully inside the chamber.8.5 Measure the density of the test paint in accordance withTes
