1、Designation:D786322Standard Guide forEvaluation of Convective Heat Transfer Coefficient ofLiquids1This standard is issued under the fixed designation D7863;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A n
2、umber in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This guide covers general information,without specificlimits,for selecting methods for evaluating the heating andcooling performance of liq
3、uids used to transfer heat whereforced convection is the primary mode for heat transfer.Further,methods of comparison are presented to effectivelyand easily distinguish performance characteristics of the heattransfer fluids.1.2 The values stated in SI units are to be regarded asstandard.No other uni
4、ts of measurement are included in thisstandard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicabil
5、ity of regulatory limitations prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the Wor
6、ld Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D445 Test Method for Kinematic Viscosity of Transparentand Opaque Liquids(and Calculation of Dynamic Viscos-ity)D1298 Test Method for Density,Relative Density,or APIGravity of Crude Petroleum and
7、 Liquid Petroleum Prod-ucts by Hydrometer MethodD2270 Practice for Calculating Viscosity Index from Kine-matic Viscosity at 40 C and 100 CD2717 Test Method for Thermal Conductivity of Liquids(Withdrawn 2018)3D2766 Test Method for Specific Heat of Liquids and Solids(Withdrawn 2018)3D2879 Test Method
8、for Vapor Pressure-Temperature Rela-tionship and Initial Decomposition Temperature of Liq-uids by IsoteniscopeD2887 Test Method for Boiling Range Distribution of Pe-troleum Fractions by Gas ChromatographyD4052 Test Method for Density,Relative Density,and APIGravity of Liquids by Digital Density Mete
9、rD4175 Terminology Relating to Petroleum Products,LiquidFuels,and LubricantsD4530 Test Method for Determination of Carbon Residue(Micro Method)D6743 Test Method for Thermal Stability of Organic HeatTransfer FluidsD7042 Test Method for Dynamic Viscosity and Density ofLiquids by Stabinger Viscometer(a
10、nd the Calculation ofKinematic Viscosity)E659 Test Method for Autoignition Temperature of Chemi-cals3.Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1For definitions of terms used in this guide,refer toTerminology D4175.3.1.2 heat transfer fluid,na fluid which remains essen-tially
11、 a liquid while transferring heat to or from an apparatus orprocess,although this guide does not preclude the evaluation ofa heat transfer fluid that may be used in its vapor state.3.1.2.1 DiscussionHeat transfer fluids may be hydrocar-bon or petroleum based such as polyglycols,esters,hydroge-nated
12、terphenyls,alkylated aromatics,diphenyl-oxide/biphenylblends,and mixtures of di-and triaryl-ethers.Small percent-ages of functional components such as antioxidants,anti-wearandanti-corrosionagents,TBN,acidscavengers,ordispersants,or a combination thereof,can be present.1This guide is under the juris
13、diction of ASTM Committee D02 on PetroleumProducts,Liquid Fuels,and Lubricants and is the direct responsibility of Subcom-mittee D02.L0.06 on Non-Lubricating Process Fluids.Current edition approved July 1,2022.Published August 2022.Originallyapproved in 2013.Last previous edition approved in 2017 as
14、 D7863 17.DOI:10.1520/D7863-22.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this
15、historical standard is referenced onwww.astm.org.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally r
16、ecognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.13.1.3 heat transfer coeffcient,na term,h,used to relatethe amount of heat transfer per unit area at a given temperaturedifference between two media and for purposes of this guide,the temperature difference is between a flow media and itssurrounding conduit.3.1.3.
