收藏 分享(赏)

ASTM_D_7966_-_D_7966M_-_14.pdf

上传人:益****师 文档编号:173103 上传时间:2023-03-04 格式:PDF 页数:7 大小:273.41KB
下载 相关 举报
ASTM_D_7966_-_D_7966M_-_14.pdf_第1页
第1页 / 共7页
ASTM_D_7966_-_D_7966M_-_14.pdf_第2页
第2页 / 共7页
ASTM_D_7966_-_D_7966M_-_14.pdf_第3页
第3页 / 共7页
ASTM_D_7966_-_D_7966M_-_14.pdf_第4页
第4页 / 共7页
ASTM_D_7966_-_D_7966M_-_14.pdf_第5页
第5页 / 共7页
ASTM_D_7966_-_D_7966M_-_14.pdf_第6页
第6页 / 共7页
亲,该文档总共7页,到这儿已超出免费预览范围,如果喜欢就下载吧!
资源描述

1、Designation:D7966/D7966M14Standard Test Method forResistance to Creep of Adhesives in Static Shear byCompression Loading(Wood-to-Wood)1This standard is issued under the fixed designation D7966/D7966M;the number immediately following the designation indicates theyear of original adoption or,in the ca

2、se of revision,the year of last revision.A number in parentheses indicates the year of lastreapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers the determination of creepproperties of structural adhesives in wood-to-

3、wood bondswhen a standardized specimen is subjected to shearing stressesat various levels of static load,constant temperature,andrelative humidity.Apparatus and procedures are provided forshear deformation(creep)of adhesive bonds under static load.This test method is used under the indicated conditi

4、ons toevaluate resistance to creep properties of a structural woodadhesive.1.2 The test method is used to evaluate creep performanceof adhesives suitable for the bonding of wood,includingtreated wood,into structural wood products for generalconstruction,marine use,or for other uses where a high-stre

5、ngth general construction,creep-resistant,durable adhesivebond is required.Individual block shear specimens are pre-pared from adhesively bonded laminations,subjected to aconstant load under various combinations of temperature andrelative humidity,and the amount of creep measured.1.3 Creep of struct

6、ural wood adhesives as measured by thistest method may not be comparative to other ASTM methodsand is limited to the conditions of the test and procedurescontained herein.1.4 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard.The values stated ineach sy

7、stem may not be exact equivalents;therefore,eachsystem shall be used independently of the other.Combiningvalues from the two systems may result in non-conformancewith the standard.1.5 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsi

8、bility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2D905 Test Method for Strength Properties of AdhesiveBonds in Shear by Compression LoadingD907 Te

9、rminology of AdhesivesD1101 Test Methods for Integrity of Adhesive Joints inStructural Laminated Wood Products for Exterior UseD2395 Test Methods for Density and Specific Gravity(Rela-tive Density)of Wood and Wood-Based MaterialsD2559 Specification for Adhesives for Bonded StructuralWood Products fo

10、r Use Under Exterior Exposure Condi-tionsD4442 Test Methods for Direct Moisture Content Measure-ment of Wood and Wood-Based MaterialsE4 Practices for Force Verification of Testing Machines2.2 Other Document:3CSA O112.9 Evaluation of Adhesives for Structural WoodProducts(Exterior Exposure)2.3 ASTM Ad

11、juncts:Compression-Shear Creep Test Apparatus43.Terminology3.1 Definitions:Many terms in this test method are definedin Terminology D907.3.1.1 laminated wood,nthe fabricated product resultingfrom the bonding of two or more laminations,with eachlamination made from one or more pieces bonded eitherlen

12、gthwise,edgewise,or both,and all with the direction of thegrain essentially parallel,to form a larger piece such as astructural member.3.1.1.1 DiscussionLaminated wood as defined in D1101.3.1.2 stress,nthe force exerted per unit area at a pointwithin a plane.3.2 Definitions of Terms Specific to This

13、 Standard:1This test method is under the jurisdiction of ASTM Committee D14 onAdhesives and is the direct responsibility of Subcommittee D14.30 on WoodAdhesives.Current edition approved Nov.1,2014.Published March 2015.DOI:10.1520/D7966_D7966-14.2For referenced ASTM standards,visit the ASTM website,w

14、ww.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from APA The Engineered Wood Association,7011 S.19th St.,Tacoma,WA 98466-5333,www.apawood.org.4Available from

15、ASTM International Headquarters.Order Adjunct No.ADJ-ADJD4680.Original adjunct produced in 1987.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 3.2.1 average creep of specimen,ncalculated creep dis-placement in the bondline of a specimen

16、as shown in Fig.1(D1+D2)/2.3.2.2 maximum average creep,nthe largest average creepobserved with any one test specimen from a test assembly.3.2.3 overall average creep,nthe average creep observedin the test assembly based on the average creep of the testedspecimens.3.2.4 laminated test assembly,nan assembly formed bybonding layers of lumber with an adhesive so that the grain ofall laminations is essentially parallel.4.Summary of Test Method4.1 An adhesive to be evaluated for suitability in structu

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2