收藏 分享(赏)

ASTM_D_6957_-_12.pdf

上传人:益****师 文档编号:173235 上传时间:2023-03-04 格式:PDF 页数:2 大小:83.58KB
下载 相关 举报
ASTM_D_6957_-_12.pdf_第1页
第1页 / 共2页
ASTM_D_6957_-_12.pdf_第2页
第2页 / 共2页
亲,该文档总共2页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation:D695712Standard Practice forMeasuring Curl in Paint Brush Filling Material1This standard is issued under the fixed designation D6957;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in pa

2、rentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This practice describes the procedure for measuring curlin synthetic filament.1.2 This practice is applicable to filament 2 to 5 in.(50.8 to127 mm)in l

3、ength.1.3 This practice is applicable to tapered filament or levelfilament.1.4 This practice is applicable to loose filling material andmaterial removed from a brush.1.5 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to

4、 SI units that are provided for information onlyand are not considered standard.1.6 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determ

5、ine the applica-bility of regulatory limitations prior to use.2.Terminology2.1 Definitions of Terms Specific to This Standard:2.1.1 paint brush filament,na synthetic polymer extrusionused in brushing material.2.1.2 filament curl,ndeviation from straight,along thelength of a filament.2.1.3 butt-end,n

6、the larger end of a tapered filament;either end of a level filament.3.Significance and Use3.1 It is important for the manufacturing and performance ofa brush to have filaments with minimal curl.4.Apparatus4.1 Filament curl deviation chart.See Fig.1.5.Procedure5.1 For Testing Synthetic Filaments:5.1.

7、1 Select filaments to be measured.5.1.2 Allow filaments to acclimate to room temperature 70to 75F(21 to 24C)at least two hours.5.1.3 Place a filament on the filament curl deviation chartwith butt-end at the x-reference point(see Fig.1).5.1.4 Record the degree of deviation from straight at theother e

8、nd of the filament.5.1.5 If multiple filaments of the same type and length are tobe measured,repeat 5.1.3 and 5.1.4 for each of the remainingfilaments and average the results.6.Keywords6.1 curl;filament1This practice is under the jurisdiction of ASTM Committee D01 on Paint andRelated Coatings,Materi

9、als,and Applications and is the direct responsibility ofSubcommittee D01.61 on Paint Application Tools.Current edition approved June 1,2012.Published July 2012.Originally approvedin 2003.Last previous edition approved in 2008 as D6957 08.DOI:10.1520/D6957-12.Copyright ASTM International,100 Barr Har

10、bor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard.Users of this standard are expressly advised that determination of the validity of any

11、 such patent rights,and the riskof infringement of such rights,are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised,either reapproved or withdrawn.Your comments are invite

12、d either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters.Your comments will receive careful consideration at a meeting of theresponsible technical committee,which you may attend.If you feel that your comments have not received a fai

13、r hearing you shouldmake your views known to the ASTM Committee on Standards,at the address shown below.This standard is copyrighted by ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959,United States.Individual reprints(single or multiple copies)of this standard ma

14、y be obtained by contacting ASTM at the aboveaddress or at 610-832-9585(phone),610-832-9555(fax),or serviceastm.org(e-mail);or through the ASTM website(www.astm.org).Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center,222Rosewood Drive,Danvers,MA 01923,Tel:(978)646-2600;http:/ Filament Curl Deviation ChartD6957 122

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2