1、Designation:D825622aStandard Test Method forEvaluation of Automotive Engine Oils for Inhibition ofDeposit Formation in the Sequence VH Spark-IgnitionEngine Fueled with Gasoline and Operated Under Low-Temperature,Light-Duty Conditions1This standard is issued under the fixed designation D8256;the numb
2、er immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.INTRODUCTIONPor
3、tions of this test method are written for use by laboratories that make use of ASTM TestMonitoring Center(TMC2)services(see Annex A1).The TMC provides reference oils,and engineering and statistical services to laboratories that desireto produce test results that are statistically similar to those pr
4、oduced by laboratories previouslycalibrated by the TMC.In general,the Test Purchaser decides if a calibrated test stand is to be used.Organizations such asthe American Chemistry Council require that a laboratory use the TMC services as part of their testregistration process.In addition,the American
5、Petroleum Institute and the Gear Lubricant ReviewCommittee of the Lubricant Review Institute(SAE International)require that a laboratory use theTMC services in seeking qualification of oils against their specifications.The advantage of using the TMC services to calibrate test stands is that the test
6、 laboratory(andhence the Test Purchaser)has an assurance that the test stand was operating at the proper level of testseverity.It should also be borne in mind that results obtained in a non-calibrated test stand may notbe the same as those obtained in a test stand participating in the ASTM TMC servi
7、ces process.Laboratories that choose not to use the TMC services may simply disregard these portions.ASTM International policy is to encourage the development of test procedures based on genericequipment.It is recognized that there are occasions where critical/sole-source equipment has beenapproved
8、by the technical committee(surveillance panel/task force)and is required by the testprocedure.The technical committee that oversees the test procedure is encouraged to clearly identifyif the part is considered critical in the test procedure.If a part is deemed to be critical,ASTMencourages alternati
9、ve suppliers to be given the opportunity for consideration of supplying the criticalpart/component providing they meet the approval process set forth by the technical committee.An alternative supplier can start the process by initiating contact with the technical committee(current chairs shown on AS
10、TM TMC website).The supplier should advise on the details of the partthat is intended to be supplied.The technical committee will review the request and determinefeasibility of an alternative supplier for the requested replacement critical part.In the event that areplacement critical part has been i
11、dentified and proven equivalent the sole-source supplier footnoteshall be removed from the test procedure.1This test method is under the jurisdiction of ASTM Committee D02 onPetroleum Products,Liquid Fuels,and Lubricants and is the direct responsibility ofSubcommittee D02.B0.01 on Passenger Car Engi
12、ne Oils.Current edition approved April 1,2022.Published April 2022.Originallyapproved in 2019.Last previous edition approved in 2022 as D8256 22.DOI:10.1520/D8256-22A.2Until the next revision of this test method,the ASTM Test Monitoring Centerwill update changes in the test method by means of inform
13、ation letters.Informationletters may be obtained from the ASTM Test Monitoring Center,203 ArmstrongDrive,Freeport,PA 16229.Attention:Director.This edition incorporates revisionsin all Information Letters through No.21-2.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken
14、,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization
15、Technical Barriers to Trade(TBT)Committee.11.Scope*1.1 This test method is commonly referred to as the Se-quence VH test,and it has been correlated with the SequenceVG test.The Sequence VG test was previously correlated withvehicles used in stop-and-go service prior to 1996,particularlywith regard t
16、o sludge and varnish formation.3It is one of thetest methods required to evaluate oils intended to satisfy theAPI SN,SN Plus performance category.1.2 The values stated in SI units are to be regarded as thestandard.No other units of measurement are included in thisstandard.1.2.1 ExceptionWhere there is no direct SI equivalentsuch as screw threads,national pipe threads/diameters,tubingsize,or specified single source equipment.1.3 A table of contents follows:SectionScope1Referenced Documents2Termin
