收藏 分享(赏)

ASTM_E_2685_-_15_2019.pdf

上传人:益****师 文档编号:173548 上传时间:2023-03-04 格式:PDF 页数:2 大小:92.78KB
下载 相关 举报
ASTM_E_2685_-_15_2019.pdf_第1页
第1页 / 共2页
ASTM_E_2685_-_15_2019.pdf_第2页
第2页 / 共2页
亲,该文档总共2页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation:E268515(Reapproved 2019)An American National StandardStandard Specification forSteel Blades Used with the Photovoltaic Module Surface CutTest1This standard is issued under the fixed designation E2685;the number immediately following the designation indicates the year oforiginal adoption

2、or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification specifies the recommended physicalcharacteristics of the steel bl

3、ades required for the surface cuttest described inANSI/UL 1703(Section 24)and IEC 61730-2(Paragraph 10.3).1.2 ANSI/UL 1703 and IEC 61730-2 are standards forphotovoltaic module safety testing.1.3 This standard provides additional fabrication details forthe surface cut test blades that are not provide

4、d in ANSI/UL1703 or IEC 61730-2.Surface cut test blades that haveout-of-tolerance corner radii or burrs are known to causeerroneous test results,either passes or failures.1.4 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.5 Th

5、is standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.6 This i

6、nternational standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)

7、Committee.2.Referenced Documents2.1 ASTM Standards:2A506 Specification for Alloy and Structural Alloy Steel,Sheet and Strip,Hot-Rolled and Cold-RolledA684/A684M Specification for Steel,Strip,High-Carbon,Cold-RolledE772 Terminology of Solar Energy Conversion2.2 International Electrotechnical Commissi

8、on Standards3IEC 61730-2 Photovoltaic(PV)Module Safety Qualifica-tion Part 2:Requirements for Testing2.3 American National Standard:4ANSI/UL 1703 Flat-Plate Photovoltaic Modules and Panels3.Terminology3.1 DefinitionsDefinitions of terms used in this specifica-tion may be found in A506,A684/A684M,E77

9、2,ANSI/UL1703,and IEC 61730-2.4.Materials and Manufacture4.1 Surface cut test blades are fabricated from hardenedsteel strips.The minimum hardness of the steel is 24 asmeasured using the Rockwell scale.Fully hardened and tem-pered steel of at least 0.50 weight percent carbon as specifiedin Specifica

10、tions E772 or A506 will meet this requirement.4.2 Other materials besides hardened steel may be usedprovided they have sufficient hardness.NOTE1Steel hacksaw blades commonly available at hardware storesare acceptable materials of the correct thickness and hardness.5.Dimensions and Permissible Variat

11、ions5.1 Blade thickness:0.64 6 0.05 mm.5.2 Corner angle:90 6 2(see Fig.1)5.3 Corner radius:0.115 6 0.025 mm(see Fig.1)6.Workmanship,Finish,and Appearance6.1 The corner contact area of the blade is intended to be acylindrical surface of the required radius;any burrs or sharppoints are removed using a

12、 steel file.7.Number of Tests and Retests7.1 The surface cut test blade may be reused until the radiusis outside the specified limits(see 5.3).1This specification is under the jurisdiction of ASTM Committee E44 on Solar,Geothermal and OtherAlternative Energy Sources and is the direct responsibility

13、ofSubcommittee E44.09 on Photovoltaic Electric Power Conversion.Current edition approved April 1,2019.Published April 2019.Originallyapproved in 2009 Last previous edition approved in 2015 as E268515.DOI:10.1520/E2685-15R19.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact

14、 ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from International Electrotechnical Commission(IEC),3 rue deVaremb,Case postale 131,CH-1211,Geneva 20,Switzerland,http:/www.iec.ch.

15、4Available from American National Standards Institute(ANSI),25 W.43rd St.,4th Floor,New York,NY 10036,http:/www.ansi.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internatio

16、nally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 7.2 The surface cut test blade may be reshaped according toSection 8 to achieve the required radius as necessary.8.Blade Preparation8.1 Secure a steel strip(see 4.1)in a metal-jawed vise.8.2 Bend the steel strip until it breaks,leaving a corner withthe re

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2