收藏 分享(赏)

ASTM_E_2639_-_12_2018.pdf

上传人:益****师 文档编号:173605 上传时间:2023-03-04 格式:PDF 页数:11 大小:267.86KB
下载 相关 举报
ASTM_E_2639_-_12_2018.pdf_第1页
第1页 / 共11页
ASTM_E_2639_-_12_2018.pdf_第2页
第2页 / 共11页
ASTM_E_2639_-_12_2018.pdf_第3页
第3页 / 共11页
ASTM_E_2639_-_12_2018.pdf_第4页
第4页 / 共11页
ASTM_E_2639_-_12_2018.pdf_第5页
第5页 / 共11页
ASTM_E_2639_-_12_2018.pdf_第6页
第6页 / 共11页
亲,该文档总共11页,到这儿已超出免费预览范围,如果喜欢就下载吧!
资源描述

1、Designation:E263912(Reapproved 2018)Standard Test Method forBlast Resistance of Trash Receptacles1This standard is issued under the fixed designation E2639;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A n

2、umber in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method provides a procedure for characterizingthe performance of a trash receptacle when an explosive isdetonated within the recep

3、tacle.1.1.1 The procedure determines the extent and location offragments produced during the explosion,and whetherbreaches are created in the exterior surfaces of the trashreceptacle.1.1.2 Appendix X1 provides guidance for determining themagnitude of blast waves(that is,external overpressures)develo

4、ped.1.1.3 Effects due to a fireball resulting from the detonationof an explosive within a trash receptacle are beyond the scopeof the test method.1.2 This test method is intended to be performed in open-airtest arenas.1.3 The values stated in SI units are to be regarded as thestandard.The values sta

5、ted in parentheses are for informationonly.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability

6、of regulatory limitations prior to use.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World T

7、rade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D638 Test Method for Tensile Properties of PlasticsD747 Test Method for Apparent Bending Modulus of Plas-tics by Means of a Cantilever BeamD790 Test Methods for Flexural Properties of Unreinforcedand

8、 Reinforced Plastics and Electrical Insulating Materi-alsD882 Test Method for Tensile Properties of Thin PlasticSheetingD883 Terminology Relating to PlasticsE2740 Specification for Trash Receptacles Subjected toBlast Resistance Testing2.2 Government Standards:DOD 4145.26 M Department of Defense:DOD

9、ContractorsSafety Manual for Ammunition and Explosives3DOD 6055.9 STD Department of Defense:DOD Ammuni-tion and Explosives Safety Standards4Voluntary Product Standard PS 1 Structural Plywood53.Terminology3.1 For terminology generally associated with explosives,refer to the glossaries given in DOD 41

10、45.26 M and DOD6055.9 STD.3.1.1 Some of the definitions in this standard(3.2)are eitheradopted as exact copies,or are adapted,from DOD 4145.26 M.Where adapted,changes to the DOD definitions were madeonly to clarify the meaning or to incorporate related terms thatalso are defined in this terminology

11、section.3.1.2 The DOD source is identified parenthetically at theright margin following the definition.3.2 Definitions:3.2.1 alias,na false low-frequency component that ap-pears when reconstructing analog data that are sampled at aninsufficient rate.3.2.2 detonation,n(1)a violent chemical reaction w

12、ithin achemical compound or mechanical mixture resulting in heatand pressure;(2)a reaction that proceeds through the reactedmaterial toward the unreacted material at a supersonic velocity.1This test method is under the jurisdiction of ASTM Committee E54 onHomeland Security Applications and is the di

13、rect responsibility of SubcommitteeE54.08 on Operational Equipment.Current edition approved Jan.1,2018.Published January 2018.Originallyapproved in 2009.Last previous edition approved in 2012 as E2639 12.DOI:10.1520/E2639-12R18.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcon

14、tact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from the Defense Technical Information Center,8725 John J.Kingman Road,Suite 0944,Ft.Belvoir,VA 22060 6128.4Available from the

15、worldwide web at:http:/www.ddesb.pentagon.mil/DoD6055.9-STD%205%20Oct%202004.pdf.5Available from the worldwide web at http:/ts.nist.gov/Standards/Conformity/upload/PS%201%20final%20complete%20w%20cover.pdf.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959

16、.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 3.2.2.1 DiscussionThe result of the chemical reaction isexertion of extremely high pressure on the surrounding me-dium forming a propagating shock wave that is originally

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2