收藏 分享(赏)

ASTM_D_6750_-_19e1.pdf

上传人:益****师 文档编号:173643 上传时间:2023-03-04 格式:PDF 页数:70 大小:2.45MB
下载 相关 举报
ASTM_D_6750_-_19e1.pdf_第1页
第1页 / 共70页
ASTM_D_6750_-_19e1.pdf_第2页
第2页 / 共70页
ASTM_D_6750_-_19e1.pdf_第3页
第3页 / 共70页
ASTM_D_6750_-_19e1.pdf_第4页
第4页 / 共70页
ASTM_D_6750_-_19e1.pdf_第5页
第5页 / 共70页
ASTM_D_6750_-_19e1.pdf_第6页
第6页 / 共70页
亲,该文档总共70页,到这儿已超出免费预览范围,如果喜欢就下载吧!
资源描述

1、Designation:D6750191Standard Test Methods forEvaluation of Engine Oils in a High-Speed,Single-CylinderDiesel Engine1K Procedure(0.4%Fuel Sulfur)and 1NProcedure(0.04%Fuel Sulfur)1This standard is issued under the fixed designation D6750;the number immediately following the designation indicates the y

2、ear oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1NOTEEditorially updated TMC governance information in June 2022.INTROD

3、UCTIONPortions of this test method are written for use by laboratories that make use of ASTM TestMonitoring Center(TMC)2services(see Annex A1 Annex A4).The TMC provides reference oils,and engineering and statistical services to laboratories that desireto produce test results that are statistically s

4、imilar to those produced by laboratories previouslycalibrated by the TMC.In general,the Test Purchaser decides if a calibrated test stand is to be used.Organizations such astheAmerican Chemistry Council require that a laboratory utilize the TMC services as part of their testregistration process.In a

5、ddition,the American Petroleum Institute and the Gear Lubricant ReviewCommittee of the Lubricant Review Institute(SAE International)require that a laboratory use theTMC services in seeking qualification of oils against their specifications.The advantage of using the TMC services to calibrate test st

6、ands is that the test laboratory(andhence the Test Purchaser)has an assurance that the test stand was operating at the proper level of testseverity.It should also be borne in mind that results obtained in a non-calibrated test stand may notbe the same as those obtained in a test stand participating

7、in the ASTM TMC services process.Laboratories that choose not to use the TMC services may simply disregard these portions.ASTM International policy is to encourage the development of test procedures based on genericequipment.It is recognized that there are occasions where critical/sole-source equipm

8、ent has beenapproved by the technical committee(surveillance panel/task force)and is required by the testprocedure.The technical committee that oversees the test procedure is encouraged to clearly identifyif the part is considered critical in the test procedure.If a part is deemed to be critical,AST

9、Mencourages alternative suppliers to be given the opportunity for consideration of supplying the criticalpart/component providing they meet the approval process set forth by the technical committee.An alternative supplier can start the process by initiating contact with the technical committee(curre

10、nt chairs shown on ASTM TMC website).The supplier should advise on the details of the partthat is intended to be supplied.The technical committee will review the request and determinefeasibility of an alternative supplier for the requested replacement critical part.In the event that areplacement cri

11、tical part has been identified and proven equivalent the sole-source supplier footnoteshall be removed from the test procedure.1These test methods are under the jurisdiction of ASTM Committee D02 onPetroleum Products,Liquid Fuels,and Lubricants and is the direct responsibility ofSubcommittee D02.B0.

12、02 on Heavy Duty Engine Oils.Current edition approved May 1,2019.Published June 2019.Originallyapproved in 2002.Last previous edition approved in 2018 as D6750 18.DOI:10.1520/D6750-19E01.2Until the next revision of this test method,the ASTM Test Monitoring Centerwill update changes in the test metho

13、d by means of information letters.Informationletters may be obtained from the ASTM Test Monitoring Center,203 ArmstrongDrive,Freeport,PA 16229.Attention:Director.This edition incorporates revisionsin all information Letters through No.18-1.Copyright ASTM International,100 Barr Harbor Drive,PO Box C7

14、00,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World

15、 Trade Organization Technical Barriers to Trade(TBT)Committee.11.Scope*1.1 These test methods cover the performance of engine oilsintended for use in certain diesel engines.They are performedin a standardized high-speed,single-cylinder diesel engine byeither the 1K(0.4%mass fuel sulfur)or 1N(0.04%ma

16、ss fuelsulfur)procedure.3The only difference in the two test methodsis the fuel used.Piston and ring groove deposit-formingtendency and oil consumption are measured.Also,the piston,the rings,and the liner are examined for distress and the ringsfor mobility.These test methods are required to evaluate oilsintended to satisfy API service categories CF-4 and CH-4 for1K,and CG-4 for 1N of Specification D4485.1.2 These test methods,although based on the originalCaterpillar 1K/1N procedures,3also embod

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2