收藏 分享(赏)

ASTM_D_6788_-_02_2017.pdf

上传人:益****师 文档编号:173662 上传时间:2023-03-04 格式:PDF 页数:4 大小:82.60KB
下载 相关 举报
ASTM_D_6788_-_02_2017.pdf_第1页
第1页 / 共4页
ASTM_D_6788_-_02_2017.pdf_第2页
第2页 / 共4页
ASTM_D_6788_-_02_2017.pdf_第3页
第3页 / 共4页
ASTM_D_6788_-_02_2017.pdf_第4页
第4页 / 共4页
亲,该文档总共4页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation:D678802(Reapproved 2017)Standard Specification forRepositionable Pressure-Sensitive Flags1This standard is issued under the fixed designation D6788;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision

2、.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers repositionable pressure-sensitive flags used to mark,flag,and index documents,books,periodicals,and so forth.1

3、.2 The values stated in either inch-pound or SI units are tobe regarded separately as standard.The values stated in eachsystem are not exact equivalents;therefore,each system mustbe used independently,without combining values in any way.1.3 The following safety hazards caveat pertains only to thetes

4、t methods portion,Section 14,of this specification.Thisstandard does not purport to address all of the safety concerns,if any,associated with its use.It is the responsibility of the userof this standard to establish appropriate safety and healthpractices and determine the applicability of regulatory

5、 require-ments prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organi

6、zation TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D996 Terminology of Packaging and Distribution Environ-mentsD3330/D3330M Test Method for PeelAdhesion of Pressure-Sensitive TapeD3652/D3652M Test Method for Thickness of Pressure-Sensitive TapesD3715/D3715M Pra

7、ctice for Quality Assurance of Pressure-Sensitive TapesD3811/D3811M Test Method for Unwind Force of Pressure-Sensitive TapesD3951 Practice for Commercial PackagingD4332 Practice for Conditioning Containers,Packages,orPackaging Components for Testing2.2 Federal Specifications:CID A-A-2826 Tabs,Signal

8、(Repositionable),cancelledNovember,19,19993PPP-T-680 Federal Packaging Standard42.3 ISO Standard:ISO 9002 Quality Systems Model for Quality Assurance inProduction and Installation52.4 ANSI/ASQC Standard:ANSI/ASQC Z 1.9 Sampling and Tables for Inspection byVariables for Percent Defective53.Terminolog

9、y3.1 DefinitionsGeneral terms in this specification are de-fined in Terminology D996.3.2 pad of flagsa vertical stack of individual flags withone flag positioned on top of the other.4.Significance and Use4.1 The repositionable,pressure-sensitive flags covered bythis specification are intended for ma

10、rking,flagging,andindexing of documents,books,periodicals,and so forth.Flagsconsist of a single sheet of matte film partially covered byadhesive.There is a non-adhesive tab or section at one end ofthe flag for easy removal from surfaces.The flag is removablefrom most surfaces including paper.Flags m

11、ay have a printedmessage on the top side of the flag.4.2 This specification replaces U.S.Government CID A-A-2826.5.Classification5.1 Type 1 flags are 1 in.wide(25 mm)and have a coloredtab at one end.1This specification is under the jurisdiction of ASTM Committee D10 onPackaging and is the direct res

12、ponsibility of Subcommittee D10.14 on Tape andLabels.Current edition approved Sept.1,2017.Published September 2017.Originallyapproved in 2002.Last previous edition approved in 2012 as D6788 02(2012).DOI:10.1520/D6788-02R17.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact

13、ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from U.S.Government Printing Office Superintendent of Documents,732 N.Capitol St.,NW,Mail Stop:SDE,Washington,DC 20401,http:/www.acc

14、ess.gpo.gov.4Available from www.dia.mil.For additional information or comments write toGeneral Services Administration,Federal Supply Service,FSS Aquisition Manage-ment Center,Environmental Programs and Engineering Policy Division(FCOE),Washington,DC 20406.5Available from American National Standards

15、 Institute(ANSI),25 W.43rd St.,4th Floor,New York,NY 10036,http:/www.ansi.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardizat

16、ion established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 5.2 Type 2 flags are 1 in.wide(25 mm)and have a printedmessage on the top side of the flag.5.3 Type 3 flags are 2 in.wide(50 mm)and have a white tabat one end to highlight writing.5.4 Type 4 flags are12in.wide(12 mm)and have a coloredtab at one end.5.5 Type 5 flags are12in.wide(12 mm)and have an a

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2