1、Designation:D72115Designation:158/69(85)Standard Test Method forOil Content of Petroleum Waxes1This standard is issued under the fixed designation D721;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A numbe
2、r in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope*1.1 This test method covers the determination of oil inpetrole
3、um waxes having a congealing point of 30 C(86 F)orhigher as determined in accordance with Test Method D938,and containing not more than 15%of oil.2NOTE1With some types of waxes,of oil contents greater than 5%,there may be an incompatibility with MEK resulting in the formation oftwo liquid phases.If
4、this occurs,the test method is not applicable to thematerial under test.1.2 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.3 This stand
5、ard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM S
6、tandards:3D938 Test Method for Congealing Point of PetroleumWaxes,Including PetrolatumE1 Specification for ASTM Liquid-in-Glass ThermometersE128 Test Method for Maximum Pore Diameter and Perme-ability of Rigid Porous Filters for Laboratory Use2.2 Energy Institute Standards:Specification for IP Stand
7、ard Thermometers43.Summary of Test Method3.1 The sample is dissolved in methyl ethyl ketone,thesolution cooled to 32 C(25 F)to precipitate the wax,andfiltered.The oil content of the filtrate is determined byevaporating the methyl ethyl ketone and weighing the residue.4.Significance and Use4.1 The oi
8、l content of a wax may have significant effects onseveral of its properties,such as strength,hardness,flexibility,scuff resistance,coefficient of friction,coefficient of expansion,melting point,and oil straining.The importance of these effectsmay be dependent upon the ultimate use of the wax.5.Appar
9、atus5.1 Filter Stick and Assembly,consisting of a 10 mm diam-eter sintered glass filter stick of 10 m to 15 m maximum porediameter as determined by the method in Appendix X1,provided with an air pressure inlet tube and delivery nozzle.Itis provided with a ground-glass joint to fit a 25 mm by 170 mmt
10、est tube.The dimensions for a suitable filtration assembly areshown in Fig.1.NOTE2A metallic filter stick may be employed if desired.A filterstick made of stainless steel and having a 12.7 mm(12in.)disk of 10 mto 15 m maximum pore diameter,as determined by Test Method E128,has been found to be satis
11、factory.5The metallic apparatus is inserted intoa 25 mm by 150 mm test tube and held in place by means of a cork.1This test method is under the jurisdiction of ASTM Committee D02 onPetroleum Products,Liquid Fuels,and Lubricants and is the direct responsibility ofSubcommittee D02.10.0A on Physical/Ch
12、emical Properties.Current edition approved June 1,2015.Published June 2015.Originallyapproved in 1943.Last previous edition approved in 2011 as D721 06(2011).DOI:10.1520/D0721-15.In the IP,this test method is under the jurisdiction of the StandardizationCommittee.This test method was issued as a joi
13、nt ASTM-IP tentative in 1964.This test method was prepared jointly by the Technical Association of Pulp andPaper Industry and ASTM International.This test method has been adopted for use by government agencies to replaceMethod 5431 of Federal Test Method Standard No.79lb.2This test method is being u
14、sed by some laboratories for products of higher oilcontent.3For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.4Availa
15、ble from Energy Institute,61 New Cavendish St.,London,WIG 7AR,U.K.5The sole source of supply of a suitable metal filter stick with designatedporosity G known to the committee at this time is the Pall Corporation,2200Northern Boulevard East Hills,NY 11548.A list of United Kingdom suppliers canbe obta
16、ined from Energy Institute,61 New Cavendish St.,London,W1G 7AR,United Kingdom.If you are aware of alternative suppliers,please provide thisinformation to ASTM International Headquarters.Your comments will receivecareful consideration at a meeting of the responsible technical committee,1whichyou may attend.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 5.2 Cooling Bath,c
