收藏 分享(赏)

ASTM_D_5958_-_99_2020.pdf

上传人:益****师 文档编号:173749 上传时间:2023-03-04 格式:PDF 页数:6 大小:106.81KB
下载 相关 举报
ASTM_D_5958_-_99_2020.pdf_第1页
第1页 / 共6页
ASTM_D_5958_-_99_2020.pdf_第2页
第2页 / 共6页
ASTM_D_5958_-_99_2020.pdf_第3页
第3页 / 共6页
ASTM_D_5958_-_99_2020.pdf_第4页
第4页 / 共6页
ASTM_D_5958_-_99_2020.pdf_第5页
第5页 / 共6页
ASTM_D_5958_-_99_2020.pdf_第6页
第6页 / 共6页
亲,该文档总共6页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation:D595899(Reapproved 2020)Standard Practices forPreparation of Oil-Based Ink Resin Solutions1This standard is issued under the fixed designation D5958;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revisio

2、n.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 These practices describe laboratory procedures for pre-paring an oil-based ink resin solution in a high-boiling solventusing four piece

3、s of lab equipment:(1)A hot oil bath(Sections 4 to 11),(2)A stirrer/hot plate(Sections 12 to 16),(3)An industrial blender(Sections 17 to 22),and(4)A hot air gun(Sections 23 to 27).ASTM Subcommittee D01.37 recommends using the hot oilbath procedure(Practice D5597)where possible.1.2 These practices us

4、e laboratory equipment generallyavailable in a normal,well-equipped laboratory.1.3 One or several of these practices allows for rapid resinsolution preparation(under 30 min,typical),can regulate themaximum temperature,can be done under an inert atmosphere,and can prevent the random solvent loss duri

5、ng preparation.1.4 These procedures are for use with ink resins intendedmainly for oil-based offset and letterpress inks.The type ofresins are typically,but not limited to C9aromatic hydrocarbonresins,modified dicyclopentadiene resins,rosin pentaerythritolor glycerine esters,phenolic modified rosin

6、esters,maleicanhydride modified rosin esters,and naturally occurring resinssuch as gilsonite.1.5 The typical high boiling solvents to be used include C12to C16petroleum distillates,2,2,4 trimethyl 1,3-pentanedioldi-isobutyrate,2alkali refined linseed oil,tridecyl alcohol,orcombinations of the above.

7、1.6 To avoid fire or injury,or both,to the operator,thesepractices should not be used with low flash point solvents suchas toluene or xylene.The minimum flash point of the solventsused should be 60C(140F)as determined by Test MethodD56.(WarningUsers of this practice should be aware thatthe flash poi

8、nt of many solvents used for this test(as defined inTest Methods D56 and D1310)is exceeded in the heating cycleof this test method.Take safety precautions since there is thepotential for vapor ignition.Do the methods outlined in ashielded exhaust hood,where there is access to a fire extin-guisher if

9、 needed.)1.7 The values stated in SI units are to be regarded asstandard.The values given in parentheses are for informationonly.1.8 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish ap

10、pro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.For specific hazard statement see 25.11.1.9 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established

11、 in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:3D56 Test Method for Flash Point by Tag Closed Cup TesterD1310 Test Method

12、 for Flash Point and Fire Point of Liquidsby Tag Open-Cup ApparatusD1725 Practice for Preparing Resin Solutions for ViscosityMeasurement by Bubble Time MethodD5062 Test Method for Resin Solution Dilutability byVolumetric/Gravimetric DeterminationD5597 Practice for Preparation of Oil-Based Ink ResinS

13、olutions Using a Hot Oil Bath(Withdrawn 1999)4E1 Specification for ASTM Liquid-in-Glass ThermometersE230 Specification for Temperature-Electromotive Force(emf)Tables for Standardized Thermocouples1These practices are under the jurisdiction of ASTM Committee D01 on Paintand Related Coatings,Materials

14、,and Applications and are the direct responsibilityof Subcommittee D01.37 on Ink Vehicles.Current edition approved June 1,2020.Published July 2020.Originally approvedin 1996.Last previous edition approved in 2012 as D5958 99(2012)1.DOI:10.1520/D5958-99R20.2The sole source of supply of the plasticize

15、r TXIB known to the committee atthis time is Eastman Chemical Company,/Texas E.M.Division,P.O.Box 7444,Longview,TX 75607-7444.If you are aware of alternative suppliers,please providethis information to ASTM International Headquarters.Your comments will receivecareful consideration at a meeting of th

16、e responsible technical committee,1whichyou may attend.3For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.4The last approved version of this historical standard is referenced onwww.astm.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2