1、Designation:D618300(Reapproved 2015)Standard Test Method forTackiness of Finish on Leather1This standard is issued under the fixed designation D6183;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number i
2、n parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope1.1 This test method is intended for use on finished leatherto eva
3、luate the tendency of cloth to adhere to it.This testmethod does not apply to wet blue.1.2 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and
4、 determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2D1517 Terminology Relating to LeatherD1610 Practice for Conditioning Leather and Leather Prod-ucts for TestingD2813 Practice for Sampling Leather for Physical andChemical Tests3.Terminology
5、3.1 Definitions of terms used in this test method can befound in Terminology D1517.3.2 Definitions of Terms Specific to This Standard:3.2.1 tackiness,adjthe tendency of cloth to adhere toleather.4.Summary of Test Method4.1 Finished leather is brought into contact with a test clothunder a prescribed
6、pressure.The apparatus is heated for aprescribed time,then cooled to room temperature.The clothsubsequently is peeled from the finished leather while observ-ing the force to remove the cloth and deformation of thefinished leather surface.5.Significance and Use5.1 This test method is intended for use
7、 on any type offinished leather.5.2 This test will give an indication of the tackiness of thefinish on leather.6.Apparatus6.1 A circulating oven capable of maintaining 50 6 2C(122 6 3.6F).6.2 A piece of bleached cheesecloth measuring at least 10by 10 cm(3.94 by 3.94 in.).6.3 A suitable device for ma
8、intaining a pressure of 100g/cm2(1.42 lb/in.2)over the entire surface of the cheesecloth.7.Sampling,Test Specimens,and Test Units7.1 Sample leather according to Practice D2813.7.2 The leather sample shall be larger than the cheesecloth.8.Conditioning8.1 Prepare the test pieces according to Practice
9、D1610.8.2 Conditioning,other than as prescribed,shall be docu-mented in the results.9.Procedure9.1 The finished leather specimen,the cheesecloth,and thedevice for maintaining pressure shall be placed in the ovenseparately and brought to the required temperature.9.2 Apply the cheesecloth to the surfa
10、ce of the leather.Apply and maintain a pressure of 100 g/cm2evenly over thesurface of the cheesecloth for 5 min while remaining in theoven.9.3 Remove the pressure from the cheesecloth,and removethe finished leather and cheesecloth while still in contact withit from the oven.9.4 Allow the finished le
11、ather and cheesecloth to cool underconditions specified by Practice D1610.9.5 Hold the test specimen vertically and at a distance of 206 2 cm(7.8 6 0.8 in.)and an angle of 45 6 5.Blow for notmore than 1 s,and observe if the cheesecloth dislodges fromthe finished leather.1This test method is under th
12、e jurisdiction of ASTM Committee D31 on Leatherand is the direct responsibility of Subcommittee D31.07 on Physical Properties.Current edition approved May 1,2015.Published July 2015.Originally approvedin 1997.Last previous edition approved in 2010 as D6183 00(2010).DOI:10.1520/D6183-00R15.2For refer
13、enced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshoho
14、cken,PA 19428-2959.United States1 9.6 Slowly pull or peel the cheesecloth from the finishedleather while observing for any tendency of the cloth to adhereto the finished leather.9.7 Observe the surface of the finished leather for deforma-tion caused by the removal of the cheesecloth and for remnants
15、of cheesecloth fibers after a puff of air is applied as in 9.5.9.8 Observe the cheesecloth for any leather finish adheringto it.10.Interpretation of Results10.1 Rank the tackiness in accordance with Table 1.11.Report11.1 Report the following information:11.1.1 Conditions used in Section 8.11.1.2 The
16、 time pressure was applied,if different from thistest method,and11.1.3 Rank in Table 1 of each test piece in the sample.12.Precision and Bias12.1 No information is presented about either the precisionor bias of this test method,since the test result is nonquanti-tative.13.Keywords13.1 leather;tackinessASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard.Users of this standard are expressly advised that de
