1、Designation:D619522Standard Test Methods forLoop Tack1This standard is issued under the fixed designation D6195;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of l
2、ast reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 These test methods cover the determination of proper-ties of a pressure-sensitive adhesive.These test methods areapplicable to those adhesives that form a bond of measurablestrength ra
3、pidly upon contact with another surface.Tack forcemay be measured as the force required to separate the adhesivefrom the adherend at the interface shortly after they have beenbrought into contact under a load equal only to the weight ofthe pressure-sensitive article(for example,tape,label,sticker,et
4、c.)on a 1 in.2contact area.1.2 The following test methods are included:1.2.1 Test Method A(using Tensile Tester),and1.2.2 Test Method B(using Loop Tack Tester).1.3 The values stated in inch-pound units are to be regardedas the standard because the industry standard width forpressure-sensitive tape i
5、s 1 inch.The values given in paren-theses are mathematical conversions to SI units that areprovided for information only and are not considered standard.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this
6、standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision
7、 on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2A666 Specification for Annealed or Cold-Worked AusteniticStainless Steel Sheet,Strip,Plat
8、e,and Flat BarD907 Terminology of AdhesivesD2651 Guide for Preparation of Metal Surfaces forAdhesiveBondingE4 Practices for Force Calibration and Verification of Test-ing MachinesE171 Practice for Conditioning and Testing Flexible BarrierPackagingE177 Practice for Use of the Terms Precision and Bias
9、 inASTM Test MethodsE691 Practice for Conducting an Interlaboratory Study toDetermine the Precision of a Test Method2.2 European Association for the Pre-Adhesed LabelingIndustry(FINAT)Standard:3FTM 9“Quick-Stick”Tack Measurement2.3 Tag and Label Manufacturers Institute,Inc.(TLMI)Standard:4L-IB1 TLMI
10、 Loop Tack TestL-IB2 Tensile Tester Loop Tack Test3.Terminology3.1 Definitions:3.1.1 Many of the terms found in these test methods aredefined in Terminology D907.4.Summary of Test Method4.1 These test methods involve allowing a loop of pressure-sensitive adhesive with its backing to be brought into
11、con-trolled contact with a 1 in.2(25 mm by 25 mm)surface ofstainless steel,with the only force applied being the weight ofthe pressure-sensitive article itself.The pressure-sensitive ar-ticle is then removed from the substrate,with the force toremove the pressure-sensitive article from the adherend
12、mea-sured by a recording instrument.4.2 Test Method A(using a Tensile Tester)applies when aTensile Tester is used to measure loop tack and involves the useof a loop prepared from an 7 in.(175 mm)specimen strip.1These test methods are under the jurisdiction of ASTM Committee D10 onPackaging and are t
13、he direct responsibility of Subcommittee D10.14 on Tape andLabels.Current edition approved Oct.1,2022.Published November 2022.Originallyapproved in 1997.Last previous edition approved in 2019 as D6195 03(2019).DOI:10.1520/D6195-22.2For referenced ASTM standards,visit the ASTM website,www.astm.org,or
14、contact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from FINAT,Laan van Nieuw-Oost Indi 131-G 2593 BM,TheHague,P.O.Box 85612,2508 CH The Hague,The Netherlands,http:/.4Available
15、 from TLMI,6 Main St.,Milford,OH 45150,https:/ ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Princi
16、ples for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.14.3 Test Method B(using a Loop Tack Tester)applies whena Loop Tack Tester is used to measure loop tack and involvesthe use of a loop prepared from a 5 in.(125 mm)specimenstrip.5.Significance and Use5.1 These test methods provide a quantitative measure ofthe pressure-sensitive tack property of an adhesive.5.2 These test methods are designe
