收藏 分享(赏)

ASTM_D_5636_-_D_5636M_-_94_2017.pdf

上传人:益****师 文档编号:174848 上传时间:2023-03-04 格式:PDF 页数:2 大小:70.18KB
下载 相关 举报
ASTM_D_5636_-_D_5636M_-_94_2017.pdf_第1页
第1页 / 共2页
ASTM_D_5636_-_D_5636M_-_94_2017.pdf_第2页
第2页 / 共2页
亲,该文档总共2页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation:D5636/D5636M94(Reapproved 2017)Standard Test Method forLow Temperature Unrolling of Felt or Sheet Roofing andWaterproofing Materials1This standard is issued under the fixed designation D5636/D5636M;the number immediately following the designation indicates theyear of original adoption or

2、,in the case of revision,the year of last revision.A number in parentheses indicates the year of lastreapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers the procedure for the physicaltesting and analysis of surface

3、cracking due to low temperatureunrolling of roofing composed of bituminous impregnated feltsand reinforced polymer modified bituminous sheet materials.These products may employ various surfacing materials on oneside.1.2 The values stated in either SI units or inch-pound unitsare to be regarded separ

4、ately as standard.The values stated ineach system may not be exact equivalents;therefore,eachsystem shall be used independently of the other.Combiningvalues from the two systems may result in non-conformancewith the standard.1.3 This standard does not purport to address all of thesafety concerns,if

5、any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.1.4 This international standard was developed in accor-dance with internationally recognized

6、principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D1079 Terminology Relating to R

7、oofing and Waterproofing3.Terminology3.1 DefinitionsFor definitions of terms used in this testmethod,see Terminology D1079.4.Summary of Test Method4.1 The felt or sheet roofing or waterproofing material roll istemperature conditioned.Specimens are then taken from theroll,wrapped around a mandrel,tem

8、perature conditioned,unrolled,and inspected for cracking.5.Significance and Use5.1 Since felts or sheet roofing or waterproofing materialsare brought to the roof in a roll and unrolled,this test methodsimulates felt or membrane behavior under actual field condi-tions during the unrolling process.5.2

9、 This test method is designed to aid those interested inthe physical properties of roofing and waterproofing felts andsheet materials.5.3 This test method enables a researcher to measure therelative behavior of low temperature unrolling of roofing andwaterproofing felt or sheet materials under labor

10、atory condi-tions.5.4 The data obtained from this test method will not permitservice life prediction or the ability of the material to beinstalled at the tested temperature.Unrolling capabilities areimportant during application,and the temperature at the time ofunrolling is believed to affect the pe

11、rformance of roofing andwaterproofing membranes.However,the actual link betweenthe test data and performance is unknown and is dependent onthe materials and exposure.6.Apparatus6.1 The mandrel for the test procedure is a 680 mm 3.125in.outer diameter(Schedule 30)PVC pipe,a minimum 6250mm 10.0 in.in

12、length.7.Test Method7.1 Unrolling at Low TemperaturesThis test method de-termines the temperature at which no cracking is observed inthe felt or sheet roofing or waterproofing materials afterunrolling at the test temperature from a 680 mm 3.125 in.diameter mandrel.7.2 Sampling:7.2.1 The specimens ar

13、e to be taken from a roll of roofing orwaterproofingmaterialsconditionedat23 6 3C1This test method is under the jurisdiction ofASTM Committee D08 on Roofingand Waterproofing and is the direct responsibility of Subcommittee D08.20 onRoofing Membrane Systems.Current edition approved May 1,2017.Publish

14、ed May 2017.Originallyapproved in 1994.Last previous edition approved in 2011 as D5636/D5636M 94(2011)1.DOI:10.1520/D5636_D5636M94R17.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume informat

15、ion,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization establ

16、ished in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 73.6 6 3.4F and 50 6 5%relative humidity for 24 h.Nospecimens are to be taken closer than 61.22 m 4 ft.from theleading edge or closer than 6150 mm 6 in.from the side ofthe roll.7.2.2 Cut four specimens from the roll in the longitudinaldirection.The specimens shall be 6250 mm(63 mm)10 in.6 18in.wide by 6450

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2