1、Designation:D5737/D5737M19Standard Guide forMethods for Measuring Well Discharge1This standard is issued under the fixed designation D5737/D5737M;the number immediately following the designation indicates theyear of original adoption or,in the case of revision,the year of last revision.A number in p
2、arentheses indicates the year of lastreapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This guide covers an overview of methods to measurewell discharge.This guide is an integral part of a series ofstandards prepared on the in-situ dete
3、rmination of hydraulicproperties of aquifer systems by single-or multiple-well tests.Measurement of well discharge is a common requirement tothe determination of aquifer and well hydraulic properties.1.2 This guide does not establish a fixed procedure for anymethod described.Rather,it describes diff
4、erent methods formeasuring discharge from a pumping or flowing well.Apumping well is one type of control well.A control well canalso be an injection well or a well in which slug tests areconducted.1.3 This guide does not address borehole flow meters thatare designed for measuring vertical or horizon
5、tal flow within aborehole.1.4 UnitsThe values stated in either SI units or inch-pound units presented in brackets are to be regarded sepa-rately as standard.The values stated in each system may not beexact equivalents;therefore,each system shall be used inde-pendently of the other.Combining values f
6、rom the two systemsmay result in non-conformance with the standard.Reporting ofresults in units other than SI shall not be regarded as noncon-formance with this standard.1.5 This guide offers an organized collection of informationor a series of options and does not recommend a specificcourse of acti
7、on.This document cannot replace education orexperience and should be used in conjunction with professionaljudgment.Not all aspects of this guide may be applicable in allcircumstances.This ASTM standard is not intended to repre-sent or replace the standard of care by which the adequacy ofa given prof
8、essional service must be judged,nor should thisdocument be applied without consideration of a projects manyunique aspects.The word“Standard”in the title of thisdocument means only that the document has been approvedthrough the ASTM consensus process.1.6 All observed and calculated values shall confo
9、rm to theguidelines for significant digits and rounding established inPractice D6026.1.6.1 The procedures used to specify how data are collected/recorded or calculated in the standard are regarded as theindustry standard.In addition,they are representative of thesignificant digits that generally sho
10、uld be retained.The proce-dures used do not consider material variation,purpose forobtaining the data,special purpose studies,or any consider-ations for the users objectives;and it is common practice toincrease or reduce significant digits of reported data to becommensurate with these considerations
11、.It is beyond the scopeof this standard to consider significant digits used in analysismethods for engineering data.1.7 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate sa
12、fety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.Furthermore,it is the users responsibility to properly disposeof water discharged.1.8 This international standard was developed in accor-dance with internationally recognized principles on
13、 standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D653 Terminology Relating to Soil,Rock,and C
14、ontainedFluidsD1941 Test Method for Open Channel Flow Measurementof Water with the Parshall FlumeD3740 Practice for Minimum Requirements for AgenciesEngaged in Testing and/or Inspection of Soil and Rock asUsed in Engineering Design and ConstructionD4043 Guide for Selection of Aquifer Test Method inD
15、etermining Hydraulic Properties by Well Techniques1This guide is under the jurisdiction ofASTM Committee D18 on Soil and Rockand is the direct responsibility of Subcommittee D18.21 on Groundwater andVadose Zone Investigations.Current edition approved Nov.1,2019.Published December 2019.Originallyappr
16、oved in 1995.Last previous edition approved in 2014 as D5737 14.DOI:10.1520/D5737_D5737M-19.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesT
