1、Designation:D543615Standard Specification forCast Poly(Methyl Methacrylate)Plastic Rods,Tubes,andShapes1This standard is issued under the fixed designation D5436;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revisi
2、on.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope*1.1 This specification covers poly(methyl methacryla
3、te)rods,tubes,and other shapes produced by casting or machiningcast blanks.This specification does not apply to heat-formedand molded or extruded parts and shapes,or sections that aremade by assembling or joining two or more pieces.NOTE1The properties included in this specification are those require
4、dto identify the types and grades of materials covered.There may be otherrequirements necessary to identify particular characteristics.1.2 The values stated in SI units are to be regarded asstandard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its us
5、e.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.NOTE2There is no known ISO equivalent to this standard.2.Referenced Documents2.1 ASTM Standards:2D542 Test Method for I
6、ndex of Refraction of TransparentOrganic PlasticsD570 Test Method for Water Absorption of PlasticsD618 Practice for Conditioning Plastics for TestingD638 Test Method for Tensile Properties of PlasticsD648 Test Method for Deflection Temperature of PlasticsUnder Flexural Load in the Edgewise PositionD
7、792 Test Methods for Density and Specific Gravity(Rela-tive Density)of Plastics by DisplacementD883 Terminology Relating to PlasticsD1003 Test Method for Haze and Luminous Transmittanceof Transparent PlasticsD1600 Terminology forAbbreviated Terms Relating to Plas-ticsD3892 Practice for Packaging/Pac
8、king of PlasticsE29 Practice for Using Significant Digits in Test Data toDetermine Conformance with Specifications3.Terminology3.1 The terminology used in this specification is in accor-dance with Terminology D883 and Terminology D1600.4.Classification4.1 TypesThis specification covers two types of
9、castmethacrylate plastics:4.1.1 Type UVAMaterial having ultraviolet-lightabsorbingproperties as shown in Table 1.4.1.2 Type UVTMaterial not subject to the light-absorbingproperties shown in Table 1.4.2 FinishCastings may be specified with the followingfinishes:4.2.1 Finish 1Rods,tubes,and shapes hav
10、ing a smoothsurface finish obtained either in the casting process or byhighly polishing the surface.4.2.2 Finish 2Rods,tubes,and shapes having a rough,unfinished surface which may be frosted,abraded,sanded,machined,or as-cast.NOTE3The sawed ends of Finish 1 and Finish 2 rods,tubes,andshapes are not
11、polished.5.General Requirements5.1 Finish 1 and Finish 2 cast tubes are subject to thefollowing permissible variations from the specified dimen-sions:5.1.1 Cast tubes shall be specified with either Type A orType B wall thickness tolerances as listed in Table 2.Type Atolerances are specified for appl
12、ications where wall thickness iscritical to performance,otherwise Type B is generally speci-fied.5.1.2 Cast tubes are subject to the outside-diameter toler-ances listed in Table 3.1This specification is under the jurisdiction of ASTM Committee D20 onPlastics and is the direct responsibility of Subco
13、mmittee D20.15 on ThermoplasticMaterials.Current edition approved June 1,2015.Published July 2015.Originally approvedin 1993.Last previous edition approved in 2013 as D5436 13.DOI:10.1520/D5436-15.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at s
14、erviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United St
15、ates1 5.1.3 Cut-to-size lengths of cast tube are subject to thelength tolerances listed in Table 4.5.2 Finish 1 and Finish 2 cast rods are subject to thefollowing dimensions and tolerances.5.2.1 Cast rods are subject to the diameter tolerances listedin Table 5.5.2.2 Cut-to-size lengths of cast rod a
16、re subject to the lengthtolerances listed in Table 4.5.3 Tolerances for shapes other than simple rods and tubesdepend upon the shapes themselves.Tolerances for these castshapes are to be specified independently.6.Detail Requirements6.1 The following applies to all specified limits in thisspecification:For purposes of determining conformance withthis specification an observed value or a calculated value shallbe rounded to the nearest 1 MPa(100 psi)for tensile strength,and for all other properties
