1、Designation:E2726/E2726M12a(Reapproved 2017)Standard Test Method forEvaluating the Fire-Test-Response of Deck Structures toBurning Brands1This standard is issued under the fixed designation E2726/E2726M;the number immediately following the designation indicates the yearof original adoption or,in the
2、 case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method determines the fire-test-response char-acteristics of deck structures attac
3、hed to or in close proximityto primary structures.The burning brand exposures test isintended to determine the degradation modes of deckingmaterials when exposed to a burning brand on the uppersurface of a deck structure.1.2 The use of paints,coatings,stains,or other surfacetreatments for fire prote
4、ction purposes are beyond the scope ofthis test method.This test method excludes the use of paints,stains,or coatings for this fire-test-response determination.1.3 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard.The values stated ineach system may no
5、t be exact equivalents;therefore,eachsystem shall be used independently of the other.Combiningvalues from the two systems may result in non-conformancewith the standard.1.4 This standard is used to measure and describe theresponse of materials,products,or assemblies to heat andflame under controlled
6、 conditions,but does not by itselfincorporate all factors required for fire-hazard or fire-riskassessment of the materials,products,or assemblies underactual fire conditions.1.5 Fire testing of products and materials is inherentlyhazardous.Adequate safeguards for personnel and propertyshall be emplo
7、yed in conducting these tests.1.6 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory
8、 limitations prior to use.1.7 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organiza
9、tion TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D2898 Practice for Accelerated Weathering of Fire-Retardant-Treated Wood for Fire TestingD6662 Specification for Polyolefin-Based Plastic LumberDecking BoardsD7032 Specification for Establishing Performance Ratin
10、gsfor Wood-Plastic Composite and Plastic Lumber DeckBoards,Stair Treads,Guards,and HandrailsE84 Test Method for Surface Burning Characteristics ofBuilding MaterialsE108 Test Methods for Fire Tests of Roof CoveringsE176 Terminology of Fire Standards2.2 ICC Evaluation Services,Inc.:3AC 109 Acceptance
11、Criteria for Thermoplastic CompositeLumber ProductsAC 174 Acceptance Criteria for Deck Board Span Ratingsand Guardrail Systems(Guards and Handrails)3.Terminology3.1 DefinitionsFor definitions of terms used in this testmethod,refer to Terminology E176.3.2 Definitions of Terms Specific to This Standar
12、d:3.2.1 deck structure,nexterior structures comprised ofdeck boards or panels,stair treads,risers,and landings ofdecks,porches,and balconies.3.2.2 test material,nmembers that constitute the exposedsurface of the deck structures.4.Significance and Use4.1 This test method is intended to establish the
13、test protocolfor decking materials and systems.This test method is intended1This test method is under the jurisdiction of ASTM Committee E05 on FireStandards and is the direct responsibility of Subcommittee E05.14 on External FireExposures.Current edition approved Dec.15,2017.Published December 2017
14、.Originallyapproved in 2012.Last previous edition approved in 2012 as E2726/E2726M12a.DOI:10.1520/E2726_E2726M12AR17.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the
15、standards Document Summary page onthe ASTM website.3Available from International Code Council Evaluation Service,5600 WorkmanMill Road,Whittier,CA.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in
16、accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 to address a fire caused by exterior sources that involves theupper surface of the deck or structure.4.2 This test is a practical assessment of fire-test-responsecharacteristics under a prescribed fire loading.This test methodis
