1、ASTM Db23 b4 0757530 0037052 5(&Designation:D 621-64(Reapproved 1988)An American National Standard AMERICAN SOCIETY FOR TESTING AND MATERIALS 1916 Race St.,Philadelphia,Pa.19103 Reprinted from the Annual Book of ASTM Standards,Copyright ASTM If not listed in the current combined Index,will appear in
2、 the next edition.Standard Test Methods for Deformation of Plastics Under Load This standard is issued under the fixed designation D 621;the number immediately following the designation indicates the year of original adoption or,in the case of revision,the year of last revision.A number in parenthes
3、es indicates the year of last reapproval.A superscript epsilon(e)indicates an editorial change since the last revision or reapproval.These test methods have been approvedjbr w e by agencies of the Department o f Definse to replace Method 1101 of Federal Test hfetliod Standard 406.and for Listing in
4、the DoD Index of Specijications and Standards.Nor-The safety hazards caveat and the Precision and Bias section were added editorially in March 1988.The Referenced Documents section was also added,causing the renumbering of subsequent sections.1.Scope 1.1 These test methods cover the determination of
5、 the deformation under compression of nonmetallic sheet and molded plastic materials,of all classes and ail commercial thicknesses,intended for structural and insulating purposes.Two test methods are included,as follows:Test Method A-For rigid plastics.Test Method B-For nonrigid plastics.1.2 The wor
6、d deformation is used herein in the broad sense to cover(I)dimensional change due almost entirely to flow,and(2)dimensional change due to a combination of flow and shrinkage caused by loss of water or other volatile matter.The word flow as used in these test methods may describe either plastic or el
7、astic deformation or combinations thereof.NOTE 1-The values stated in SI units are to be regarded as the standard.NOTE 2-Methyl methacrylate and polystyrene are examples of materiais that deform almost entirely by flow.Cellulose acetate,cellulose acetate butyrate,phenolic laminated fiber,and vulcani
8、zed fiber are examples of materials that deform by a combination of flow and shrinkage.1.3 This standard may involve hazardoics materials,oper-alons,and eqtiipntent.This standard does not purport to address all o f the safety problems associated with its lise.It i s the responsibility o f the user o
9、 f this standard to establish appropriate safery and health practices and determine the applicQblily o f regulatory limitations prior to use.2,Referenced Documents 2.1 ASTM Standards:D374 Test Methods for Thickness of Solid Electrical D575 Test Methods for Rubber Properties in Com-Insulation2 pressi
10、on3 These test methods are under the jurisdiction of ASTM Committee D-20 on P l a s t i c s and are the direct responsibility of Subcommittee D20.30 on Thermal Properties(Section D20.30.07).Current edition approved Aug.31,1964.Published October 1964.Originally published as D 621-41.Last previous edi
11、tion D 621-59.Annical Book o f ASTM Standards,Vol 08.01.Anmial Book ofASThf Standards.Vol 09.01.D 18 Methods of Conditioning Plastics and Electrical Insulating Materials for Testing 3.Significance and Use 3.1 Data obtained by Test Method A give a measure of the abiiity of a rigid plastic in assembli
12、es of conductors and insulators that are held together by bolts,rivets,or similar fastening devices,to withstand compression without yielding and loosening the assembly with time.Test Method A also gives a measure of the rigidity of plastics at service tempera-tures and consequently can be used as a
13、n identification test for procurement purposes.3.2 Data obtained by Test Method B give a measure of the ability of a nonrigid plastic to return to its original dimen-sions with time after having been deformed.Test Method B determines the extent to which the plastic will follow associated parts in ap
14、plications requiring elastic properties.TEST METHOD A-RIGID PLASTICS 4.Nature of Test 4.1 The principle of Test Method A is essentially that of the parallel plate plastometer,namely,a constant-force system whereby a test specimen is conditioned,if necessary,and is then placed between the parallel pl
15、ates of a consfant-force device and the thickness observed over a required period at the stipulated temperature or temperatures.5.Apparatus 5.1 Testing Machine-A machine capable of exerting a constant force of 113 kg(250 lb),227 kg(500 lb),and 454 kg(1000 lb)f 1%between the parallel anvils of the ma
16、chine,which shall be arranged so that they can be brought into contact with the test specimen before the load is applied.A machine suitable for this test is shown in Fig.1.A recom-mended method for calibrating such a device is given in the Appendix.One of the anvils of the machine shall preferably be self-aligning and shall,in order that the load may be applied evenly over the face of the specimen,be arranged so that the specimen is accurately centered and the resultant of the load is through it
