1、Designation:D5867121Standard Test Methods forMeasurement of Physical Properties of Raw Cotton byCotton Classification Instruments1This standard is issued under the fixed designation D5867;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revisi
2、on,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1NOTEReference to a research report was added editorially in January 2013.1.Scope1.1 This test method covers the measur
3、ement of color,trashcontent,micronaire,upper half mean length(length),unifor-mity index and breaking tenacity(strength)of raw cotton forcotton marketing using a cotton classification instrument.1.2 This test method is applicable to Upland and Extra LongStaple(ELS)raw cotton.1.3 This test method is a
4、pplicable to roller and saw ginnedraw cottons.1.4 This test method contains the following sections.SectionColor8-11Trash Content12-15Micronaire Reading16-19Upper Half Mean Length(Length)and Uniformity Index20-23Breaking Tenacity(Strength)24-271.5 The values stated in both inch-pound and SI units are
5、 tobe regarded separately as the standard.The values given inparentheses are for information only.1.6 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health pr
6、actices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2D123 Terminology Relating to TextilesD1441 Practice for Sampling Cotton Fibers for TestingD1445 Test Method for Breaking Strength and Elongation ofCotton Fibers(Flat Bundle Metho
7、d)D1447 Test Method for Length and Length Uniformity ofCotton Fibers by Photoelectric MeasurementD1448 Test Method for Micronaire Reading of Cotton Fi-bersD1776 Practice for Conditioning and Testing TextilesD2253 Test Method for Color of Raw Cotton Using theNickerson-Hunter Cotton Colorimeter(Withdr
8、awn 1995)3D2495 Test Method for Moisture in Cotton by Oven-DryingD2812 Test Method for Non-Lint Content of CottonD3025 Practice for Standardizing Cotton Fiber Test Resultsby Use of Calibration Cotton StandardsD4848 Terminology Related to Force,Deformation andRelated Properties of TextilesD7139 Termi
9、nology for Cotton FibersE691 Practice for Conducting an Interlaboratory Study toDetermine the Precision of a Test MethodE177 Practice for Use of the Terms Precision and Bias inASTM Test Methods3.Terminology3.1 For all terminology related to D13.11,refer to D7139.3.1.1 The following terms are relevan
10、t to this standard:micronaire reading,particle count(trash),percent area(trash),Rd(color reflectance)and+b(color yellowness),breakingtenacity(strength),uniformity index,upper-half-mean length.3.2 For all other terminology related to textiles,refer toTerminology D123 and Terminology D4848.4.Significa
11、nce and UseGeneral4.1 This test method is accepted for testing of bales of rawcotton in commercial shipments.4.2 This test method describes acceptable practices fortesting of raw cotton using cotton classification instrumentsthat are capable of testing the fiber properties of micronairereading,lengt
12、h,uniformity index,strength,Rd(color),+b(color),percent area(trash)and particle count(trash).1These test methods are under the jurisdiction of ASTM Committee D13 onTextiles and are the direct responsibility of Subcommittee D13.11 on Cotton Fibers.Current edition approved July 1,2012.Published Septem
13、ber 2012.Originallyapproved in 1995.Last previous edition approved in 2005 as D5867 05.DOI:10.1520/D5867-12E01.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standa
14、rds Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 5.Sampling5.1 Bale SampleFor a bale sample,take a 4 oz(100 g)
15、subsample of cotton from each of two opposite sides of the baleand combine the two subsamples into a single bale sampleweighing 8 oz(200 g).6.Conditioning6.1 Condition the cotton samples to the temperature andrelative humidity levels of 21 6 1C(70 6 2F)and 65 6 2%until moisture equilibrium is reache
16、d.6.2 Accelerated conditioning is an acceptable practice forthis test method.6.3 Moisture content(dry basis)measured by resistancetechnique referenced to oven method Test Method D2495 shallbe within 6.75 to 8.25%.NOTE1This range covers the equilibrium moisture content range forall cottons.NOTE2Cotton is normally received in the laboratory in a relative drycondition,making special preconditioning procedures unnecessary.Samples that are obviously damp should be preconditioned before beingbrought i
