1、Designation:D53100(Reapproved 2010)Standard Test Method forRubber PropertyPusey and Jones Indentation1This standard is issued under the fixed designation D531;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.
2、A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1.Scope1.1 This test method covers the determination of the inden-t
3、ation of rubber or rubber-like materials by means of the Puseyand Jones type of plastometer.This apparatus is used tomeasure the depth of indentation of an indentor,under fixedforce into the surface of a specimen.1.2 The values stated in SI units are to be regarded as thestandard.1.3 This standard d
4、oes not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standa
5、rds:2D618 Practice for Conditioning Plastics for TestingD1415 Test Method for Rubber PropertyInternationalHardnessD4483 Practice for Evaluating Precision for Test MethodStandards in the Rubber and Carbon Black ManufacturingIndustriesNOTE1The specific dated edition of the practice that prevails in th
6、isdocument is referenced in the Section 9.3.Significance and Use3.1 The Pusey and Jones indentation value is the depth ofindentation,expressed in hundredths of a millimetre,of a ball3.175 mm(0.1250 in.)in diameter under an expressed force of9.8 N(2.2 lbf).This value may be used to compare theindenta
7、tion resistance of rubber and rubber-like materials.3.2 The indentation value obtained should not be confusedwith hardness as measured by Test Method D1415,since in thelatter test the rubber immediately adjacent to the indentor isprecompressed.4.Apparatus4.1 Plastometer,an instrument consisting of a
8、n indentor,amass for applying the stated force on the indentor,a microm-eter for indicating the depth of the indentation,a specimenholder and support.4.1.1 Indentor,for indenting the specimen,consisting of avertical steel shaft attached,at the upper end to a depthindicator gage,and terminating in a
9、steel sphere having adiameter of 3.175 6 0.015 mm(0.1250 6 0.0005 in.)ofpolished,noncorrosive hard metal treated to resist wear.4.1.2 Mass,the mass shall be 1000 6 0.01 g.4.1.3 Depth Indicator Gage,a micrometer attached to theplastometer,either an electronic digital gage or analog dialgage,capable o
10、f displaying indentor movement(indentation)in increments of at least 0.01 mm(0.0004 in.)and having travelof 0(zero)to no less than 3 mm(0.12 in).4.1.4 Support,a support frame,or fixture,for the plastome-ter,shall be configured so that the specimen holder and hence,the specimen,are perpendicular to t
11、he indentor support shaftand that the mass may be independently raised or loweredvertically,permitting the indentor to rest on the surface of thespecimen and the mass to be subsequently applied.4.1.5 Specimen Holder,for the standard,or reference speci-men described in 5.1,shall consist of a clamping
12、 fixture of twometal plates secured by two threaded bolts.The uppermostplate shall have a hole and a slot,as depicted in Fig.1,to allowfor the unencumbered introduction of the indentor to thespecimen.4.1.5.1 The purpose of the specimen holder is to support thespecimen in a manner that reduces,or eli
13、minates,relativepositioning or movement that may adversely affect test deter-minations.4.1.5.2 In routine testing,a specimen holder,a support,orboth,of other,but similar,configurations may be employed toaccommodate specimens other than those described in 5.1,refer to 5.1.1.1This test method is under
14、 the jurisdiction of ASTM Commitee D11 on Rubberand is the direct responsibility of Subcommittee D11.10 on Physical Testing.Current edition approved Jan.1,2010.Published April 2010.Originallyapproved in 1939.Last previous edition approved in 2005 as D531 00(2005).DOI:10.1520/D0531-00R10.2For referen
15、ced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohock
16、en,PA 19428-2959.United States1 5.Test Specimens5.1 The standard,or reference,test specimen shall be auniform molded rectangular block a minimum of 13 mm(0.51in.)in thickness,30 mm(1.18 in.)in width,and 75 mm(2.95in.)in length.The upper and lower surfaces,those oppositesurfaces with the largest area,shall be parallel to within 60.5mm(60.20 in).5.1.1 The standard,or reference,test specimen shall be usedwhen the plastometer is employed for the purpose of determin-ing a standard,or reference,either
