1、Designation:D474019Standard Test Method forCleanliness and Compatibility of Residual Fuels by SpotTest1This standard is issued under the fixed designation D4740;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revisio
2、n.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This test method covers separate procedures for deter-mining the cleanliness of residual fuel oil and the compatibilityof a residual f
3、uel oil with a blend stock.It is applicable toresidual fuel oils with viscosities up to 50 cSt(1 cSt=1 mm2s)at 100 C.This test method describes two protocols:onemanual and one automated.NOTE1This test method has not been evaluated for heavy distillatehaving the propensity to leave a wax sediment on
4、the filter paper andcontain no residual asphaltene.1.2 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility
5、 of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization establ
6、ished in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D4057 Practice for Manual Sampling of Petroleum andPetroleum Product
7、sD4175 Terminology Relating to Petroleum Products,LiquidFuels,and LubricantsD4177 Practice for Automatic Sampling of Petroleum andPetroleum Products2.2 ASTM Adjuncts:3Reference Spot Sheet3.Terminology3.1 For definitions of terms used in this standard,seeTerminology D4175.3.2 Definitions of Terms Spe
8、cific to This Standard:3.2.1 blend stock,none component or more componentsused to make a final fuel product.3.2.1.1 DiscussionIn heavy fuel oils,blend stocks includevarious refinery streams ranging from kerosine to heavydistillates,residuals,and asphalts.3.2.2 cleanliness,nof residual fuel,the conce
9、ntration ofsuspended solids in a finished sample.3.2.2.1 DiscussionThe lower the concentration of sus-pended solids,the cleaner the residual fuel.3.2.3 compatibility,nof residual fuel,the absence ofsuspended solids when equal volumes of a sample and a blendstock are mixed together.4.Summary of Test
10、Method4.1 Cleanliness Procedures,Manual and AutomatedAdrop of the preheated and thoroughly mixed sample is put ona test paper and placed in an oven at 100 C.After 1 h,the testpaper is removed from the oven and the resultant spot isexamined for evidence of suspended solids and rated forcleanliness us
11、ing the D4740 Adjunct Reference Spot Sheet.4.2 Compatibility Procedures,Manual and AutomatedAblend composed of equal volumes of the sample fuel oil andthe blend stock is tested in the same way as described in 4.1and rated for compatibility against D4740 Adjunct ReferenceSpot Sheet.5.Significance and
12、 Use5.1 The four procedures in this test method are used alone orin combination to identify fuels or blends that could result inexcessive centrifuge loading,strainer plugging,tank sludgeformation,or similar operating problems.1This test method is under the jurisdiction of ASTM Committee D02 onPetrol
13、eum Products,Liquid Fuels,and Lubricants and is the direct responsibility ofSubcommittee D02.14 on Stability,Cleanliness and Compatibility of Liquid Fuels.Current edition approved May 1,2019.Published June 2019.Originallyapproved in 1992.Last previous edition approved in 2014 as D4740 04(2014).DOI:1
14、0.1520/D4740-19.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from ASTM International Headquarters.Or
15、der Adjunct No.ADJD4740.Original adjunct produced in 2000.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internat
16、ionally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 5.2 A spot rating of Number 3 or higher on a finished fueloil by the cleanliness procedure indicates that the fuel containsexcessive suspended solids and is likely to cause operatingproblems.5.3 Although a fuel may test clean when subjected to thecleanl
