1、Designation:D480621aStandard Specification forDenatured Fuel Ethanol for Blending with Gasolines for Useas Automotive Spark-Ignition Engine Fuel1This standard is issued under the fixed designation D4806;the number immediately following the designation indicates the year oforiginal adoption or,in the
2、 case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This specification covers nominally anhydrous dena-tured fuel ethanol intended to be blended
3、 with unleaded orleaded gasolines at 1%to 15%by volume for use as automo-tive spark-ignition engine fuel covered by Specification D4814as well as other fuel applications or specifications involvingethanol.The significance of this specification is shown inAppendix X1.1.2 Jurisdictions may vary in the
4、ir regulatory requirementsfor the allowable or prohibited types of denaturants,chemicalcomposition of the denaturant or concentration of denaturantneeded to denature the ethanol.The user is advised to checkwith the national and regional regulatory agencies where theethanol is denatured and used.1.2.
5、1 Specific regulatory requirements for denatured fuelethanol and acceptable denaturants from various jurisdictionsare given in Appendixes for information.1.3 The values stated in SI units are to be regarded asstandard.1.3.1 ExceptionValues given in parentheses are providedfor information only.Non-SI
6、 units are shown in the Appendixif they are in a direct quotation from government regulations.In most cases,U.S.federal regulations specify non-SI units.1.4 The following safety hazards caveat pertains only to themethod modification in 8.7 of this specification:This standarddoes not purport to addre
7、ss all of the safety concerns,if any,associated with its use.It is the responsibility of the user of thisstandard to establish appropriate safety,health,and environ-mental practices and determine the applicability of regulatorylimitations prior to use.1.5 This international standard was developed in
8、 accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 AS
9、TM Standards:2D86 Test Method for Distillation of Petroleum Products andLiquid Fuels at Atmospheric PressureD381 Test Method for Gum Content in Fuels by Jet Evapo-rationD1298 Test Method for Density,Relative Density,or APIGravity of Crude Petroleum and Liquid Petroleum Prod-ucts by Hydrometer Method
10、D1613 Test Method for Acidity in Volatile Solvents andChemical Intermediates Used in Paint,Varnish,Lacquer,and Related ProductsD1688 Test Methods for Copper in WaterD2622 Test Method for Sulfur in Petroleum Products byWavelength Dispersive X-ray Fluorescence SpectrometryD3120 Test Method for Trace Q
11、uantities of Sulfur in LightLiquid Petroleum Hydrocarbons by Oxidative Microcou-lometryD4052 Test Method for Density,Relative Density,and APIGravity of Liquids by Digital Density MeterD4057 Practice for Manual Sampling of Petroleum andPetroleum ProductsD4175 Terminology Relating to Petroleum Product
12、s,LiquidFuels,and LubricantsD4177 Practice for Automatic Sampling of Petroleum andPetroleum ProductsD4306 Practice for Aviation Fuel Sample Containers forTests Affected by Trace ContaminationD4814 Specification for Automotive Spark-Ignition EngineFuelD5453 Test Method for Determination of Total Sulf
13、ur inLight Hydrocarbons,Spark Ignition Engine Fuel,DieselEngine Fuel,and Engine Oil by Ultraviolet FluorescenceD5501 Test Method for Determination of Ethanol andMethanol Content in Fuels Containing Greater than 20%1This specification is under the jurisdiction of ASTM Committee D02 onPetroleum Produc
14、ts,Liquid Fuels,and Lubricants and is the direct responsibility ofSubcommittee D02.A0.02 on Oxygenated Fuels and Components.Current edition approved Oct.1,2021.Published October 2021.Originallyapproved in 1988.Last previous edition approved in 2021 as D4806 21.DOI:10.1520/D4806-21A.2For referenced A
15、STM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM Int
16、ernational,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1Ethanol by Gas ChromatographyD5580 Test Method for Determination of Benzene,Toluene,Ethylbenzen
