1、Designation:D510307(Reapproved 2018)Standard Test Method forLength and Length Distribution of Manufactured StapleFibers(Single-Fiber Test)1This standard is issued under the fixed designation D5103;the number immediately following the designation indicates the year oforiginal adoption or,in the case
2、of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers the determination of averagestaple length and staple length distribution of
3、 both manufac-tured and natural fibers by manually measuring single fiberlengths.This test method is also used to measure the length offibers removed from a staple yarn,but such a measurementmay not represent the fibers staple length,as manufactured.1.2 Because this test method requires measuring th
4、e lengthof only 50 fibers,it is not suitable for use in determining thenumber of long fibers that occur infrequently in a sample.NOTE1For determination for overlength fibers,refer to Test MethodD3513.NOTE2For methods covering the determination of the average lengthand length distribution of natural
5、fibers,refer to the following methods:for cotton,Test Method D1440,and Test Method D1447,for wool,TestMethod D519,Test Method D1234,and Test Method D1575.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this
6、 standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decisio
7、n on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D123 Terminology Relating to TextilesD519 Test Method for Length of Fiber in Wool TopD12
8、34 Test Method of Sampling and Testing Staple Lengthof Grease WoolD1440 Test Method for Length and Length Distribution ofCotton Fibers(Array Method)D1447 Test Method for Length and Length Uniformity ofCotton Fibers by Photoelectric MeasurementD1575 Test Method for Fiber Length of Wool in ScouredWool
9、 and in Card SliverD1776 Practice for Conditioning and Testing TextilesD2258 Practice for Sampling Yarn for TestingD3333 Practice for Sampling Manufactured Staple Fibers,Sliver,or Tow for TestingD3513 Test Method for Overlength Fiber Content of Manu-factured Staple FiberD4849 Terminology Related to
10、Yarns and Fibers3.Terminology3.1 For all terminology relating to D13.58,Yarns andFibers,refer to Terminology D4849.3.1.1 The following terms are relevant to this standard:length distribution,velveteen.3.2 For all other terminology related to textiles,see Termi-nology D123.4.Summary of Test Method4.1
11、 Each fiber to be tested is gripped at the tips with forceps,fully extended without stretching,and measured.The averagefiber length of the measured fibers is calculated and the lengthdistribution curve is plotted.5.Significance and Use5.1 This test method is used for research,development,quality con
12、trol,product specifications,and may be used foracceptance testing of commercial shipments of textile fibers.However,caution is advised since information on between-laboratory precision is lacking.Comparative tests as directed in5.1.1 may be advisable.5.1.1 If there are differences of practical signi
13、ficance be-tween reported test results for two laboratories(or more),comparative tests should be performed to determine if there isa statistical bias between them,using competent statisticalassistance.As a minimum,test samples that are as homogenousas possible,drawn from the material from which the
14、disparatetest results were obtained,and randomly assigned in equal1This test method is under the jurisdiction ofASTM Committee D13 on Textilesand is the direct responsibility of Subcommittee D13.58 on Yarns and FibersCurrent edition approved July 1,2018.Published August 2012.Originallyapproved in 19
15、90.Last previous edition approved in 2012 as D5103 07(2012).DOI:10.1520/D5103-07R18.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page o
16、nthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 numbers to each laboratory for testing.The test results fr
