1、Designation:D463416Standard Classification System and Basis for Specification forStyrene-Maleic Anhydride Molding and Extrusion Materials(S/MA)1This standard is issued under the fixed designation D4634;the number immediately following the designation indicates the year oforiginal adoption or,in the
2、case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope*1.1 This cla
3、ssification system covers styrene-maleic anhy-dride materials suitable for molding or extrusion.This classi-fication system does not apply to alloys or blends of styrene-maleicanhydridematerialswithnon-elastomericthermoplastics.Styrene-maleic anhydride materials,beingthermoplastic,are reprocessable
4、and recyclable.This classifi-cation system allows for the use of those materials providedthat all the specific requirements of this classification systemare met.1.2 The properties included in this standard are thoserequired to identify the compositions covered.Other require-ments necessary to identi
5、fy particular characteristics importantto specialized applications are to be specified by using thesuffixes as given in Section 5.1.3 This classification system and subsequent line call out(specification)are intended to provide means of calling outproperties of plastic materials used in the fabricat
6、ion of enditems or parts.It is not intended for the selection of materials.Materials should be selected by those having expertise in theplastics field after careful consideration of the design and theperformance required of the part,the environment to which itwill be exposed,the fabrication process
7、to be employed,costsinvolved,and the inherent properties of the material other thanthose covered by this classification system.1.4 The values stated in SI units are to be regarded as thestandard.1.5 The following precautionary caveat pertains only to thetest methods portion,Section 11,of this classi
8、fication system.This standard does not purport to address all of the safetyconcerns,if any,associated with its use.It is the responsibilityof the user of this standard to establish appropriate safety andhealth practices and determine the applicability of regulatorylimitations prior to use.NOTE1There
9、 is no known ISO equivalent to this standard.2.Referenced Documents2.1 ASTM Standards:2D256 Test Methods for Determining the Izod PendulumImpact Resistance of PlasticsD618 Practice for Conditioning Plastics for TestingD638 Test Method for Tensile Properties of PlasticsD648 Test Method for Deflection
10、 Temperature of PlasticsUnder Flexural Load in the Edgewise Position(With-drawn 2016)3D790 Test Methods for Flexural Properties of Unreinforcedand Reinforced Plastics and Electrical Insulating Materi-alsD883 Terminology Relating to PlasticsD1525 Test Method for Vicat Softening Temperature ofPlastics
11、D1600 Terminology forAbbreviated Terms Relating to Plas-ticsD3641 Practice for Injection Molding Test Specimens ofThermoplastic Molding and Extrusion MaterialsD3892 Practice for Packaging/Packing of PlasticsD4000 Classification System for Specifying Plastic Materi-alsD7209 Guide for Waste Reduction,
12、Resource Recovery,andUse of Recycled Polymeric Materials and Products(With-drawn 2015)3E29 Practice for Using Significant Digits in Test Data toDetermine Conformance with Specifications1This classification system is under the jurisdiction ofASTM Committee D20 onPlastics and is the direct responsibil
13、ity of Subcommittee D20.15 on ThermoplasticMaterials.Current edition approved April 1,2016.Published April 2016.Originallyapproved in 1986.Last previous edition approved in 2011 as D4634-11a.DOI:10.1520/D4634-16.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Custom
14、er Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.*A Summary of Changes section appears at the end of this standardCopyr
15、ight ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 2.2 Military Standard:4MIL-STD-1916 DOD Preferred Methods for Acceptance ofProduct2.3 Underwriters Laboratories Standard:5UL 94 Standard for Tests for Flammability for Parts inDevices and Applian
16、ces3.Terminology3.1 The terminology used in this classification system is inaccordance with Terminologies D883 and D1600.4.Classification4.1 Styrene-maleic anhydride materials are classified intogroups according to their use either for injection molding,orfor extrusion.These groups are subdivided into classes andgrades,as shown in Table S/MA.NOTE2An example of this classification system is as follows:Thedesignation S/MA 211 would indicate:S/MA=Styrene-maleic anhydride,2=injection-molding resin(g
