1、Designation:D47802(Reapproved 2012)Standard Specification forZinc Yellow(Zinc Chromate)Pigments1This standard is issued under the fixed designation D478;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A numb
2、er in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1.Scope1.1 This specification covers the pigments commerciallyknown as zi
3、nc yellow(zinc chromate).1.2 Two types are included:1.2.1 Type IHigh-purity,low sulfate and chloride content.1.2.2 Type IIRegular grade.1.3 The values stated in SI units are to be regarded asstandard.The values given in parentheses are for informationonly.2.Referenced Documents2.1 ASTM Standards:2D1
4、85 Test Methods for Coarse Particles in PigmentsD387 Test Method for Color and Strength of ChromaticPigments with a Mechanical MullerD444 Test Methods for Chemical Analysis of Zinc YellowPigment(Zinc Chromate Yellow)3.Significance and Use3.1 Zinc yellow is used in rust-inhibiting protective coatings
5、and metal primers for ferrous and non-ferrous metals.4.Composition and Properties4.1 Dry PigmentThe pigment shall be a reaction precipi-tate of soluble chromates and a suitable zinc compound andshall be free of extenders,carbonates,and organic color in anyform.The pigment shall conform to the requir
6、ements forcomposition prescribed in Table 1.4.2 The mass color and character of the tint and the tintingstrength formed by a mixture with a white pigment shall bewithin mutually agreed upon limits of a standard acceptable toboth the purchaser and the seller.5.Sampling5.1 Two samples shall be taken a
7、t random from differentpackages from each lot,batch,days pack,or other unit ofproduction in a shipment.When no markings distinguishingbetween units of production appear,samples shall be takenfrom different packages in the ratio of two samples for each4545 kg(10 000 lb),except that for shipments of l
8、ess than10 000 lb two samples shall be taken.At the option of thepurchaser,the samples may be tested separately or afterblending in equal quantities the samples from the sameproduction unit to form a composite sample.6.Test Methods6.1 Tests shall be conducted in accordance with the follow-ing ASTM t
9、est methods:6.2 Chemical AnalysisTest Methods D444.6.3 Coarse ParticlesTest Methods D185.6.4 Mass Color and Tinting StrengthTest Method D387.7.Keywords7.1 chromatic;inhibitor metal primer;pigment;zinc chro-mate;zinc yellow1This specification is under the jurisdiction of ASTM Committee D01 on Paintan
10、d Related Coatings,Materials,and Applications and is the direct responsibility ofSubcommittee D01.31 on Pigment Specifications.Current edition approved June 1,2012.Published August 2012.Originallyapproved in 1938.Last previous edition approved in 2006 as D478 02(2006).DOI:10.1520/D0478-02R12.2For re
11、ferenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Consh
12、ohocken,PA 19428-2959.United States1 ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard.Users of this standard are expressly advised that determination of the validity of any such patent rights,and the risk
13、of infringement of such rights,are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised,either reapproved or withdrawn.Your comments are invited either for revision of this st
14、andard or for additional standardsand should be addressed to ASTM International Headquarters.Your comments will receive careful consideration at a meeting of theresponsible technical committee,which you may attend.If you feel that your comments have not received a fair hearing you shouldmake your vi
15、ews known to the ASTM Committee on Standards,at the address shown below.This standard is copyrighted by ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959,United States.Individual reprints(single or multiple copies)of this standard may be obtained by contacting ASTM
16、 at the aboveaddress or at 610-832-9585(phone),610-832-9555(fax),or serviceastm.org(e-mail);or through the ASTM website(www.astm.org).Permission rights to photocopy the standard may also be secured from the ASTM website(www.astm.org/COPYRIGHT/).TABLE 1 Composition RequirementsType IType IIZinc(calculated as ZnO),%35 to 4035 to 40Chromium(calculated as CrO3),min,%4141Sulfates(calculated as SO3),max,%0.203.0AChlorides(calculated as Cl),max,%0.100.8AAlkaline salts(calculated as K2O),max,%1313Matter
