收藏 分享(赏)

ASTM_D_5568_-_22.pdf

上传人:益****师 文档编号:176578 上传时间:2023-03-04 格式:PDF 页数:8 大小:146.53KB
下载 相关 举报
ASTM_D_5568_-_22.pdf_第1页
第1页 / 共8页
ASTM_D_5568_-_22.pdf_第2页
第2页 / 共8页
ASTM_D_5568_-_22.pdf_第3页
第3页 / 共8页
ASTM_D_5568_-_22.pdf_第4页
第4页 / 共8页
ASTM_D_5568_-_22.pdf_第5页
第5页 / 共8页
ASTM_D_5568_-_22.pdf_第6页
第6页 / 共8页
亲,该文档总共8页,到这儿已超出免费预览范围,如果喜欢就下载吧!
资源描述

1、Designation:D556822Standard Test Method forMeasuring Relative Complex Permittivity and RelativeMagnetic Permeability of Solid Materials at MicrowaveFrequencies Using Waveguide1This standard is issued under the fixed designation D5568;the number immediately following the designation indicates the yea

2、r oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This test method covers a procedure for determiningrelative c

3、omplex permittivity(relative dielectric constant andloss)and relative magnetic permeability of isotropic,reciprocal(non-gyromagnetic)solid materials.If the material isnonmagnetic,it is acceptable to use this procedure to measurepermittivity only.1.2 This measurement method is valid over a frequencyr

4、ange of approximately 100 MHz to over 40 GHz.These limitsare not exact and depend on the size of the specimen,the sizeof rectangular waveguide transmission line used as a specimenholder,and on the applicable frequency range of the networkanalyzer used to make measurements.The size of specimendimensi

5、on is limited by test frequency,intrinsic specimenelectromagnetism properties,and the request of algorithm.Being a non-resonant method,the selection of any number ofdiscrete measurement frequencies in a measurement bandwould be suitable.Use of multiple rectangular waveguidetransmission line sizes ar

6、e required to cover this entire fre-quency range(100 MHz to 40 GHz).This test method can alsobe generally applied to circular waveguide test fixtures.Therectangular waveguide fixture is preferred over coaxial fixtureswhen samples have in-plane anisotropy or are difficult tomanufacture precisely.1.3

7、The values stated in SI units are to be regarded as thestandard.The values given in parentheses are in inch-poundunits and are included for information only.The equationsshown here assume an e+jtharmonic time convention.1.4 This standard does not purport to address all of thesafety concerns,if any,a

8、ssociated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accor-dance with internationally re

9、cognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D1711 Terminology Rela

10、ting to Electrical Insulation3.Terminology3.1 For other definitions used in this test method,refer toTerminology D1711.3.2 Definitions:3.2.1 relative complex permittivity(relative complex dielec-tric constant),r*,nthe proportionality factor that relates theelectric field to the electric flux density

11、,and which depends onintrinsic material properties such as molecular polarizability,charge mobility,and so forth:r*5 r2 jr5DW0EW(1)where:0=the permittivity of free space,D=the electric flux density vector,andE=the electric field vector.3.2.1.1 DiscussionIn common usage the word“relative”is frequentl

12、y dropped.The real part of complex relativepermittivity(r)is often referred to as simply relativepermittivity,permittivity,or dielectric constant.The imaginarypart of complex relative permittivity(r)is often referred to asthe loss factor.In anisotropic media,permittivity is describedby a three dimen

13、sional tensor.1This test method is under the jurisdiction of ASTM Committee D09 onElectrical and Electronic Insulating Materials and is the direct responsibility ofSubcommittee D09.12 on Electrical Tests.Current edition approved March 15,2022.Published April 2022.Originallyapproved in 1994.Last prev

14、ious edition approved in 2014 as D5568 14.DOI:10.1520/D5568-22.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A

15、Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established

16、in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.13.2.1.2 DiscussionFor the purposes of this test method,the media is considered to be isotropic and,therefore,permit-tivity is a single complex number at each frequency.3.2.2 relative complex permeability,r*,nthe proportion-ality factor that relates the magnetic flux density to themagnetic field,and which depends o

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2