1、w 0759530 0549053 448 w Designation:D 5597-94 AMERICAN SOCIETY FOR TESTING AND MATERIALS 1916 Race St Philadelphia,Pa 19103 Reprinted irom the Annual Book of ASTM Standards.CopyrIght ASTM If not losted in the current combined indeq will appear m the next edition Standard Practice for Preparation of
2、Oil-Based Ink Resin Solutions Using a Hot Oil Bath This standard is issued under the fixed designation D 5597;the number immediately following the designation indicates the year of original adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of la
3、st reapproval.A superscript epsilon(0 indicates an editorial change since the last revision or reapproval.1.Scope 1.1 This practice covers a laboratory procedure for pre-paring an oil-based ink resin solution in a high boiling solvent using a hot oil bath.1.2 This practice uses laboratory equipment
4、generally available in a normal,well equipped laboratory.1.3 This practice allows rapid resin solution preparation(typically 30 to 45 min)and regulates the maximum temperature under an inert atmosphere,preventing the random solvent loss during preparation.1.4 The procedure is for use with ink resins
5、 intended mainly for oil-based offset and letterpress inks.The types of resins are typically,but not limited to,C,aromatic hydro-carbon resins,modified dicyclopentadiene resins,rosin pentaerythritol or glycerin esters,phenolic-modified rosin esters,maleic anhydride-modified rosin esters,and naturall
6、y occurring resins such as gilsonite.1.5 The typical high boiling solvents to be used include C,&,petroleum distillates,texanol isobutyrate,alkali-refined linseed oil,tridecyl alcohol,or combinations of the above.1.6 To avoid fire or injury to the operator,or both,this procedure should not be used w
7、ith low flash point solvents such as toluene or xylene.The minimum flash point of the solvents used should be 60C(14oF)as determined by Test Method D 56.1.7 This standard does not purport to address all of the safety concerns,if any,associated with its use.It is the responsibility of the user of thi
8、s standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents 2.1 ASTM Standards:D 56 Test Method for Flash Point by Tag Closed Tester2 E 1 Specification for ASTM Thermometers3 3.Terminology 3.1 Definit
9、ions:3.1.1 compatibility-resin and solvent mixture that forms a clear,homogeneous,and stable solution.r This practice is under the jurisdiction of ASTM Committee D-l on Paint and Related Coatings,Materials,and Applications and is the direct responsibility of Subcommittee DO1.37 on Ink Vehicles.Curre
10、nt edition approved Sept.IS,1994.Published November 1994.z Annual Book ojASTM Standards.VolOS.0 1.3 Annual Book of ASTM Standardr,Vol 14.03.3.1.2 dissolution-the point at which all resin dissolves completely in the solvent.3.1.3 incompatibility-resin and solvent mixture that is not compatible,when a
11、n opaque or two-phase mixture results.3.1.4 oil bath-non-volatile silicone fluid contained in a large,heat-resistant crystallizing dish heated by a tempera-ture-controlled stirrer hot plate.3.1.5 solution-resin and solvent that form a clear,com-patible,and homogeneous mixture.4.Summary of Practice 4
12、.1 The required concentration of resin and solvent is placed in a 250-mL Erlenmeyer flask.4.2 A hot oil bath is heated to the required dissolution temperature(150 to 2Oo”C,typically approximately 180C or slightly above for high softening point or poorly solvated resins).4.3 The Erlenmeyer flask cont
13、aining the mixture of resin and solvent is placed into the hot oil bath with an inert gas purge and a cold water condenser.4.4 The mixture is allowed to mix at the desired temper-ature until all of the resin is dissolved completely.4.5 The flask is removed from the hot oil bath and allowed to cool w
14、hile still under an inert atmosphere for 10 to 15 min.The sample is saved for future testing.5.Significance and Use 5.1 This practice provides a means of preparing small quantities of resin solution in an inert gas atmosphere using uniform,controlled heating.5.2 This practice provides a rapid method
15、 of preparing a resin solution for quality control testing during the manufac-ture of resin solutions and vehicles.Samples can usually be prepared in approximately 30 to 45 min.5.3 This practice can be used for preparing commonly specified ink test solutions such as 33.3%resin in alkali-refined lins
16、eed oil and 50%resin in heat-set ink solvent(that is,C12-CIb hydrocarbon petroleum distillate with initial boiling point(I.B.P.)of approximately 243C(470F).6.Apparatus 6.1 Balance,capable of weighing to+O.O 1 g accuracy.6.2 Sieve,16 mesh.6.3 Thermometer,0 to 25oC conforming to Specification E 1.6.4 Crystallizing Dish,heat resistant,150 by 75 mm.NOTICE:This standard has either been superseded and replaced by a new version or discontinued.Contact ASTM International(www.astm.org)for the latest info
