1、Designation:D553105(Reapproved 2011)Standard Guide forPreparation,Maintenance,and Distribution of PhysicalProduct Standards for Color and Geometric Appearance ofCoatings1This standard is issued under the fixed designation D5531;the number immediately following the designation indicates the year ofor
2、iginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This guide covers three levels of physical productstandards for col
3、or or appearance,or both,commonly used inthe coatings industry,provides terminology to describe eachlevel,and describes techniques for generating and caring forstandards.1.2 The values stated in SI units are to be regarded as thestandard.The values given in parentheses are for informationonly.1.3 Th
4、is standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.
5、1 ASTM Standards:2D16 Terminology for Paint,Related Coatings,Materials,andApplicationsD523 Test Method for Specular GlossD823 Practices for Producing Films of Uniform Thicknessof Paint,Varnish,and Related Products on Test PanelsD1729 Practice for Visual Appraisal of Colors and ColorDifferences of Di
6、ffusely-Illuminated Opaque MaterialsD2244 Practice for Calculation of Color Tolerances andColor Differences from Instrumentally Measured ColorCoordinatesD3134 Practice for Establishing Color and Gloss TolerancesD4086 Practice for Visual Evaluation of MetamerismD4449 Test Method for Visual Evaluation
7、 of Gloss Differ-ences Between Surfaces of Similar AppearanceE284 Terminology of AppearanceE308 Practice for Computing the Colors of Objects by Usingthe CIE SystemE430 Test Methods for Measurement of Gloss of High-GlossSurfaces by Abridged GoniophotometryE805 Practice for Identification of Instrumen
8、tal Methods ofColor or Color-Difference Measurement of MaterialsE1164 Practice for Obtaining Spectrometric Data for Object-Color EvaluationE1331 Test Method for Reflectance Factor and Color bySpectrophotometry Using Hemispherical GeometryE1345 Practice for Reducing the Effect of Variability ofColor
9、Measurement by Use of Multiple MeasurementsE1347 Test Method for Color and Color-Difference Mea-surement by Tristimulus ColorimetryE1349 Test Method for Reflectance Factor and Color bySpectrophotometry Using Bidirectional(45:0 or 0:45)Geometry2.2 Society of Automotive Engineers Standard:SAE J1545 Re
10、commended Practice for Instrumental ColorDifference Measurement for Exterior Finishes,Textiles,and Colored Trim33.Terminology3.1 The definitions in Terminology E284 and D16 areapplicable to this standard.The terms in E284 take precedenceover those in D16 if differences exist.3.2 Definitions of Terms
11、 Specific to This Standard:3.2.1 concept color,nthe color of the material submittedby the customer as the target for generating the masterstandard.3.2.2 master standard,nthe physical standard for colorthat the customer approves as the target for visual,spectropho-tometric,and colorimetric evaluation
12、 of all products referencedto that standard.3.2.2.1 DiscussionIn SAE J1545 this is referred to as the“official”standard.1This guide is under the jurisdiction of ASTM Committee D01 on Paint andRelated Coatings,Materials,and Applications and is the direct responsibility ofSubcommittee D01.26 on Optica
13、l Properties.Current edition approved June 1,2011.Published June 2011.Originallyapproved in 1994.Last previous edition approved in 2005 as D5531-05.DOI:10.1520/D5531-05R11.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual
14、 Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from Society of Automotive Engineers(SAE),400 CommonwealthDr.,Warrendale,PA 15096-0001,http:/www.sae.org.*A Summary of Changes section appears at the end of this standardCopyright AST
15、M International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 3.2.3 duplicate master standard,na replicate of the masterstandard that serves as the master standard at a secondarylocation.3.2.3.1 DiscussionIn SAE J1545 this is referred to as the“reference”standard.3
16、.2.4 working standard,nthe physical product standardfor color or appearance,or both,used for routine measurementsand visual assessments in the laboratory and at the productionsite.4.Summary of Guide4.1 Product standards are the only standards by whichproducts should be accepted or rejected for color or appear-ance.A master standard is generated from the concept colorsubmitted by the customer.Duplicate master standards,whenneeded,are generated from the master standard.Workingstandards are generat
