收藏 分享(赏)

ASTM_D_4670_-_17.pdf

上传人:益****师 文档编号:176826 上传时间:2023-03-04 格式:PDF 页数:2 大小:62KB
下载 相关 举报
ASTM_D_4670_-_17.pdf_第1页
第1页 / 共2页
ASTM_D_4670_-_17.pdf_第2页
第2页 / 共2页
亲,该文档总共2页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation:D467017Standard Test Method forPolyurethane Raw Materials:Determination of SuspendedMatter in Polyols1This standard is issued under the fixed designation D4670;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of l

2、ast revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This test method covers a procedure for visual inspec-tion to determine the presence of insoluble foreign material inpolyol

3、s.1.2 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.NOTE1There is no

4、 known ISO equivalent to this standard.2.Referenced Documents2.1 ASTM Standards:2D883 Terminology Relating to Plastics3.Terminology3.1 Terminology in this test method is in accordance withTerminology D883.4.Significance and Use4.1 This test method is suitable as a quality control orspecification tes

5、t.5.Procedure5.1 Invert a colorless,transparent glass bottle containing thewell-mixed sample and examine by transmitted light for thepresence of suspended matter.6.Report6.1 Report the presence or absence of suspended matter.7.Precision and Bias7.1 No statement is made about the precision or the bia

6、ssince this test method merely states whether suspended matteris detected or not.8.Keywords8.1 polyols;polyurethane raw materials;suspended matterSUMMARY OF CHANGESCommittee D20 has identified the location of selected changes to this standard since the last issue(D4670 07(2012)1)that may impact the

7、use of this standard.(March 1,2017)(1)Modified 7.1 to provide clearer instruction.1This test method is under the jurisdiction of ASTM Committee D20 on Plasticsand is the direct responsibility of Subcommittee D20.22 on Cellular Materials-Plastics and Elastomers.It was recommended to ASTM by the Cente

8、r for thePolyurethanes Industry Polyurethane Raw Material Analysis Workgroup.Current edition approved March 1,2017.Published March 2017.Originallyapproved in 1987.Last previous edition approved in 2012 as D4670 07(2012)1.DOI:10.1520/D4670-17.2For referenced ASTM standards,visit the ASTM website,www.

9、astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C

10、700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the Worl

11、d Trade Organization Technical Barriers to Trade(TBT)Committee.1 ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard.Users of this standard are expressly advised that determination of the validity of any suc

12、h patent rights,and the riskof infringement of such rights,are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised,either reapproved or withdrawn.Your comments are invited ei

13、ther for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters.Your comments will receive careful consideration at a meeting of theresponsible technical committee,which you may attend.If you feel that your comments have not received a fair he

14、aring you shouldmake your views known to the ASTM Committee on Standards,at the address shown below.This standard is copyrighted by ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959,United States.Individual reprints(single or multiple copies)of this standard may be

15、 obtained by contacting ASTM at the aboveaddress or at 610-832-9585(phone),610-832-9555(fax),or serviceastm.org(e-mail);or through the ASTM website(www.astm.org).Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center,222Rosewood Drive,Danvers,MA 01923,Tel:(978)646-2600;http:/ 172

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2