1、Designation:D467121Standard Test Method forPolyurethane Raw Materials:Determination of Unsaturationof Polyols1This standard is issued under the fixed designation D4671;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last
2、revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This test method measures unsaturation in polyetherpolyols.(See Note 1.)It uses 2 mL of ca.0.05 M mercuricacetate reagent in me
3、thanol and about 1 g of sample or less.This test method uses a potentiometric determination of an endpoint.1.2 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.3 Mercury has been designated by many regulatory agen-cies as a haza
4、rdous substance that can cause serious medicalissues.Mercury,or its vapor,has been demonstrated to behazardous to health and corrosive to materials.Caution shouldbe taken when handling mercury and mercury containingproducts.See the applicable product Safety Data Sheet(SDS)for additional information.
5、Users should be aware that sellingmercury and/or mercury containing products into your state orcountry may be prohibited by law.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish app
6、ro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.NOTE1This standard is equivalent to ISO 17710.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization establ
7、ished in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D883 Terminology Relating to PlasticsE180 Practice for Determining t
8、he Precision of ASTMMethods for Analysis and Testing of Industrial and Spe-cialty Chemicals(Withdrawn 2009)3E456 Terminology Relating to Quality and StatisticsE2935 Practice for Evaluating Equivalence of Two TestingProcesses2.2 ISO Standards:ISO 17710 PlasticsPolyols for Use in the Production ofPoly
9、urethaneDetermination of Degree of Unsaturationby Microtitration43.Terminology3.1 DefinitionsTerms used in this standard are defined inaccordance with Terminology D883,unless otherwise speci-fied.For terms relating to precision and bias and associatedissues,the terms used in this standard are define
10、d in accordancewith Terminology E456.4.Summary of Test Method4.1 Carbon-to-carbon unsaturated compounds in the sampleare reacted with mercuric acetate and methanol in a methanolicsolution to produce acetoxymercuricmethoxy compounds andacetic acid.5The amount of acetic acid released in thisequimolar
11、reaction,which is determined by titration withstandard alcoholic potassium hydroxide,is a measure of theunsaturation originally present.Because the acid cannot betitrated in the presence of excess mercuric acetate,due to the1These test methods are under the jurisdiction of ASTM Committee D20 onPlast
12、ics and are the direct responsibility of Subcommittee D20.22 on CellularMaterials-Plastics and Elastomers.Current edition approved July 1,2021.Published July 2021.Originally approvedin 1987.Last previous edition approved in 2016 as D4671-16.DOI:10.1520/D4671-21.2For referenced ASTM standards,visit t
13、he ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.4Available from Amer
14、ican National Standards Institute(ANSI),25 W.43rd St.,4th Floor,New York,NY 10036,http:/www.ansi.org.5Sigia,S.and Hanna,J.G.,“Quantitative Organic Analysis via FunctionalGroups,”John Wiley and Sons,New York,1979.*A Summary of Changes section appears at the end of this standardCopyright ASTM Internat
15、ional,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides an
16、d Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1formation of insoluble mercuric oxide,sodium bromide isadded to convert the mercuric acetate to the bromide,whichdoes not interfere.Inasmuch as these test methods are based onan acidimetric titration,a suitable correction must be applied ifthe sample is not neutral to phenolphthalein indicator.Takecare to exclude carbon dioxide,which titrates as an acid andgives erroneous results.5.Significance an
