1、Designation:D493106(Reapproved 2017)Standard Test Method forGross Moisture in Green Petroleum Coke1This standard is issued under the fixed designation D4931;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A
2、number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers both the preparation procedurefor samples containing free water(air drying loss(ADL)ongross moisture samples)and th
3、e determination of the grossmoisture content of green petroleum coke.1.2 The values stated in SI units are to be regarded asstandard.1.2.1 ExceptionThe values given in parentheses are forinformation only.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with i
4、ts use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accor-dance with internationally recognized princip
5、les on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D2013 Practice for Preparing Coal Samp
6、les for AnalysisD2234/D2234M Practice for Collection of a Gross Sampleof CoalD3302 Test Method for Total Moisture in CoalE11 Specification for Woven Wire Test Sieve Cloth and TestSieves3.Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 air drying,na process of partial drying of a
7、greenpetroleum coke sample to bring it to near equilibrium with theatmosphere in the room in which further reduction/division ofthe petroleum coke sample is to take place.3.1.2 air dry loss,ADL,nthe loss in mass,expressed as apercentage,resulting from each air drying operation.3.1.3 free water,nvisi
8、ble unbound water in the sample.3.1.4 green petroleum coke,nsame as raw petroleumcoke.3.1.5 gross moisture,nthat moisture determined as theloss in mass in an air atmosphere under rigidly controlledconditions of temperature,time,and air flow.3.1.5.1 DiscussionTest Method D3302 prescribes theabove con
9、trolled conditions.3.1.6 petroleum coke,nsolid,carbonaceous residue pro-duced by thermal decomposition of heavy petroleum fractions,or cracked stocks,or both.3.1.7 residual moisture,nthat moisture remaining in thesample after air drying.3.1.8 total moisture,nsynonym for gross moisture.4.Summary of T
10、est Method4.1 This test method is based on the loss in mass of a greenpetroleum coke sample in an air atmosphere under controlledconditions of temperature,time,and air flow.4.1.1 Preparation Procedure shall be used when the petro-leum coke sample contains free water.The gross moisturesample is weigh
11、ed and air dried to equilibrate it with theatmosphere.Determination of residual moisture is that deter-mined using the Drying Oven Method.Air drying and residualmoisture losses are combined to report gross moisture.4.1.2 Drying Oven Method shall be used in routine com-mercial practice when the sampl
12、e does not contain free water.The sample is crushed to at least minus 25 mm(1 in.)top sievesize and divided into analytical portions of at least 500 g each.Determination of total gross moisture is calculated by summingthe results of the Drying Oven Method and the results of thePreparation Procedure.
13、5.Significance and Use5.1 Moisture adds mass to the coke and serves no usefulpurpose.A knowledge of the moisture content is important inthe purchase and sale of green petroleum coke,both of whichare conducted on a dry basis.1This test method is under the jurisdiction of ASTM Committee D02 onPetroleu
14、m Products,Liquid Fuels,and Lubricants and is the direct responsibility ofSubcommittee D02.05 on Properties of Fuels,Petroleum Coke and Carbon Material.Current edition approved Oct.1,2017.Published November 2017.Originallyapproved in 1989.Last previous edition approved in 2011 as D4931 06(2011).DOI:
15、10.1520/D4931-06R17.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor D
16、rive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 5.2 The collection of the sample as specified for the DryingOven Method is intended for the express purpose of determin-in
