1、Designation:D588120Standard Practice for(Analytical Procedures)Determining Transmissivity ofConfined Nonleaky Aquifers by Critically Damped WellResponse to Instantaneous Change in Head(Slug)1This standard is issued under the fixed designation D5881;the number immediately following the designation in
2、dicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This practice covers determination of transmis
3、sivityfrom the measurement of water-level response to a suddenchange of water level in a well-aquifer system characterized asbeing critically damped or in the transition range from under-damped to overdamped.Underdamped response is character-ized by oscillatory changes in water level;overdamped re-s
4、ponse is characterized by return of the water level to the initialstatic level in an approximately exponential manner.Over-damped response is covered in Guide D4043;underdampedresponse is covered in Practice D5785/D5785M,Guide D4043.1.2 The analytical procedure in this practice is used inconjunction
5、 with Guide D4043 and the field procedure in TestMethod D4044/D4044M for collection of test data.1.3 LimitationsSlug tests are considered to provide anestimate of the transmissivity of an aquifer near the wellscreen.The method is applicable for systems in which thedamping parameter,is within the ran
6、ge from 0.2 through 5.0.The assumptions of the method prescribe a fully penetratingwell(a well open through the full thickness of the aquifer)ina confined,nonleaky aquifer.1.4 All observed and calculated values shall conform to theguidelines for significant digits and rounding established inPractice
7、 D6026.1.4.1 The procedures used to specify how data are collected/recorded and calculated in this standard are regarded as theindustry standard.In addition,they are representative of thesignificant digits that should generally be retained.The proce-dures used do not consider material variation,purp
8、ose forobtaining the data,special purpose studies,or any consider-ations for the users objectives;and it is common practice toincrease or reduce significant digits of reported data to com-mensurate with these considerations.It is beyond the scope ofthis standard to consider significant digits used i
9、n analysismethods for engineering design.1.5 UnitsThe values stated in SI units are to be regardedas standard.No other units of measurement are included in thisstandard.Reporting of results in units other than SI shall not beregarded as nonconformance with this standard.1.6 This practice offers a se
10、t of instructions for performingone or more specific operations.This document cannot replaceeducation or experience and should be used in conjunction withprofessional judgment.Not all aspects of the practice may beapplicable in all circumstances.This ASTM standard is notintended to represent or repl
11、ace the standard of care by whichthe adequacy of a given professional service must be judged,nor should this document be applied without the considerationof a projects many unique aspects.The word“Standard”in thetitle of this document means only that the document has beenapproved through he ASTM con
12、sensus process.1.7 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations pr
13、ior to use.1.8 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalB
14、arriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D653 Terminology Relating to Soil,Rock,and ContainedFluidsD3740 Practice for Minimum Requirements for AgenciesEngaged in Testing and/or Inspection of Soil and Rock as1This test method is under the jurisdiction ofASTM Committee
15、D18 on Soil andRock and is the direct responsibility of Subcommittee D18.21 on Groundwater andVadose Zone Investigations.Current edition approved June 1,2020.Published June 2020.Originallyapproved in 1995.Last previous edition approved in 2018 as D5881 18.DOI:10.1520/D5881-20.2For referenced ASTM st
16、andards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardizatio
