1、Designation:D522522Standard Test Method forMeasuring Solution Viscosity of Polymers with a DifferentialViscometer1This standard is issued under the fixed designation D5225;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of l
2、ast revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This test method covers the determination of the solu-tion viscosity of polymers using a differential or the modifieddiffer
3、ential viscometer.It is applicable to all polymers thatdissolve completely without chemical reaction or degradationto form solutions that are stable with time and temperature.Results of the test are usually expressed as specific viscosity,intrinsic viscosity(limiting viscosity number),inherent visco
4、s-ity(logarithmic viscosity number),or relative viscosity(vis-cosity ratio).1.2 Since there is more than one type of viscometer avail-able to measure a differential pressure,follow the manufactur-ers directions applicable to the equipment being used.1.3 The solution viscosity values are comparable w
5、ith thoseobtained using a glass capillary of Test Method D2857.Thistest method differs from the glass capillary in that the solventand the solution are compared at the same time that a test isrun.With a glass capillary,each solution must be referencedback to the solvent run in the same capillary at
6、the sametemperature.1.4 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.5 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard t
7、o establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.For specific hazard statements,see Section 8.NOTE1There is no known ISO equivalent to this standard.1.6 This international standard was developed in accor-dance
8、with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:
9、2D883 Terminology Relating to PlasticsD1243 Test Method for Dilute Solution Viscosity of VinylChloride PolymersD1600 Terminology forAbbreviated Terms Relating to Plas-ticsD2857 Practice for Dilute Solution Viscosity of PolymersE456 Terminology Relating to Quality and StatisticsE691 Practice for Cond
10、ucting an Interlaboratory Study toDetermine the Precision of a Test MethodE2935 Practice for Evaluating Equivalence of Two TestingProcesses3.Terminology3.1 Definitions:3.1.1 For definitions of terms pertaining to plastics used inthis test method,refer to Terminology D883.For abbreviationsused in thi
11、s test method,refer to terminology D1600,unlessotherwise indicated.For definitions of terms that appear in thistest method relating to quality and statistics,refer to Terminol-ogy E456.3.1.2 inherent viscosity,nthe ratio of the natural logarithmof the relative viscosity to the concentration.The IUPA
12、C termfor inherent viscosity is logarithmic viscosity number.3.1.3 intrinsic viscosity,nlimit of the reduced and inherentviscosities as the concentration of the polymeric solute ap-proaches zero and represents the capacity of the polymer toincrease viscosity.The IUPAC term for intrinsic viscosity is
13、limiting viscosity number.3.1.4 reduced viscosity,nthe ratio of the specific viscosityto the concentration.Reduced viscosity is a measure of thespecific capacity of the polymer to increase the relativeviscosity.The IUPAC term for reduced viscosity is viscositynumber.1This test method is under the ju
14、risdiction of ASTM Committee D20 on Plasticsand is the direct responsibility of Subcommittee D20.70 on Analytical Methods.Current edition approved Sept.1,2022.Published September 2022.Originallyapproved in 1992.Last previous edition approved in 2017 as D5225-17.DOI:10.1520/D5225-22.2For referenced A
15、STM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM Int
16、ernational,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.13.1.5 relative viscosity,nthe ratio of the polymer solutionpressure to the pressure of the solv
